Utility room fitting in Fleet

Why utility room fitting for a Fleet home?

Dog owners and keen walkers around Fleet often ask for a utility with a deep sink, a coat cupboard and somewhere to leave muddy boots and wet jackets.

If the kitchen in your Hampshire home is a narrow galley, a separate utility can take the appliances that would otherwise crowd the worktop and storage. We cover all of Fleet, including the GU13, GU51 and GU52 postcode districts, and travel out to neighbouring towns across Hampshire.

What we cover for utility room fitting in Fleet

After the survey visit we write the scope down. For utility room fitting in Fleet it usually covers:

Utility sink and tap plumbed in, with new supplies and waste where none exist
Worktop over the washing machine and dryer, supported clear of the appliances
A vent to outside for a vented dryer, or a drain hose for condenser models
Base, wall and tall units fitted, levelled and fixed to the wall
Stacking kit fitted where the washer and dryer sit one above the other
Washing machine supply, waste and isolation valve, tested for leaks

What should you budget for utility room fitting in Fleet?

These guide ranges include VAT at 20% and are adjusted for prices in the South East. We confirm your price in writing after a free survey visit. Expect costs in the South East to sit somewhat above UK averages, reflecting local labour rates.

What should you budget for utility room fitting in Fleet?
Typical project	Guide price
Utility units and worktop fitted (fit only)Three to six units, laminate worktop, panels	£1,400–£3,400
Utility room supplied and fittedUnits, worktop, sink, washer and dryer connections	£3,400–£8,000
New utility plumbing for a sink and washing machineSupplies, waste and valves where none exist	£460–£1,200

Fit-only and supply-and-fit ranges cover units, worktop and standard sink and appliance connections, with new plumbing where none exists as a separate line; extract fans, dryer vents and new circuits are quoted on top. Prices include VAT at 20%.

Local homes and their kitchens

Typical homes in this part of Hampshire include Victorian terraces, 1930s semis, post-war estate houses and thatched and brick cottages. Terraces in Southampton and Portsmouth often have a narrow back kitchen, while post-war estate houses tend to have a compact rectangular room suited to an L-shape.

Water across Hampshire is mostly hard, largely from chalk sources, so limescale on taps and boiling water taps is common and a filter can help. Dense terraced streets can be very tight for parking, and New Forest lanes and village roads may limit the size of delivery vehicle.

Regulations for kitchen work in Fleet

Fitting a utility room needs no planning permission in England, though a new dryer vent through the outside wall of a flat may need planning permission and the freeholder's consent. Adding sockets to an existing circuit is not notifiable, but a new circuit is, under Part P. Approved Document F sets an extract rate of about 30 litres per second for a utility room, so a new fan should be sized to meet it, and if an open-flued boiler shares the room, a Gas Safe registered engineer should carry out a spillage test once a fan is fitted.

Homes within the New Forest or South Downs national parks, listed cottages and conservation areas may need consent for a new extractor vent or alterations to historic features.

Before you book utility room fitting in Fleet

If your Hampshire home has an open-flued boiler in the utility, ask for a spillage test by a Gas Safe registered engineer once an extract fan goes in.
Before choosing a dryer for your Fleet utility, check whether there is an outside wall close enough for a short, straight vent duct.
Leave room behind the washing machine for the hoses; pushing it hard against the wall can kink them and stop the water draining properly.
A worktop over appliances needs support at each side and a gap above the machines, so they can be slid out for servicing.

Questions about utility room fitting in Fleet

How much does utility room fitting cost in Fleet?

For fitting three to six utility units and a worktop you have bought, budget around £1,400 to £3,400 including VAT in Fleet. That reflects typical costs in the South East; we confirm the actual figure in writing once we have measured up.

Do you work near Fleet as well?

Yes. As well as Fleet itself, we cover the rest of Hampshire and nearby towns such as Farnborough and Aldershot. The process is the same wherever the kitchen is.

Can a utility room go in a garage or under the stairs?

Often, yes, as long as the space already exists and is usable. In a garage it needs to be dry and protected from frost, with power and a route for water and waste. Under the stairs, check the headroom, the ventilation and whether a door can open fully. We fit units and connect appliances in existing spaces; converting a garage into a habitable room is a separate building project.

Does a utility room need an extractor fan?

Yes, in most cases. Washing and drying put a lot of moisture into a small space, so extract ventilation is strongly advised: Approved Document F sets a rate of about 30 litres per second for utility rooms in England and Wales, and the building standards in Scotland and Technical Booklet K in Northern Ireland cover ventilation too. An extract fan ducted outside is the usual answer, with a window helping but not replacing it. A vented dryer needs its own duct as well.

Does a condenser or heat pump dryer need an outside vent?

No. Condenser and heat pump dryers do not need an outside vent, so they can go where a vented dryer cannot. They collect water in a container that has to be emptied, or they can be connected to the waste so they drain automatically, which is easy when the dryer sits beside the washing machine. They still give off some warmth, so the space needs air around it. A vented dryer needs a duct to an outside wall.

Utility room fitting in neighbouring towns

The same service is available a short drive from Fleet, including: