Utility room fitting in Bognor Regis

Who usually needs utility room fitting in Bognor Regis?

If your Bognor Regis home has a back lobby or a rear porch with a little spare width, a few units and a stacked washer and dryer can make it a working utility.

Families in Bognor Regis often want the washing machine out of the kitchen, so the noise, the wet laundry and the drying racks have a room of their own. We work throughout Bognor Regis (PO21) and across the wider West Sussex area.

What does utility room fitting in Bognor Regis include?

Every kitchen is different, so we confirm the scope in writing. Most jobs of this kind include:

Extract fan fitted to clear moisture from washing and drying
Washing machine supply, waste and isolation valve, tested for leaks
Stacking kit fitted where the washer and dryer sit one above the other
Base, wall and tall units fitted, levelled and fixed to the wall
Worktop over the washing machine and dryer, supported clear of the appliances
Free survey visit to check water, waste, power and outside wall positions

What does utility room fitting cost in Bognor Regis?

These guide ranges include VAT at 20% and are adjusted for prices in the South East. We confirm your price in writing after a free survey visit. Expect costs in the South East to sit somewhat above UK averages, reflecting local labour rates.

What does utility room fitting cost in Bognor Regis?
Typical project	Guide price
Utility units and worktop fitted (fit only)Three to six units, laminate worktop, panels	£1,400–£3,400
Utility room supplied and fittedUnits, worktop, sink, washer and dryer connections	£3,400–£8,000
New utility plumbing for a sink and washing machineSupplies, waste and valves where none exist	£460–£1,200

Fit-only and supply-and-fit ranges cover units, worktop and standard sink and appliance connections, with new plumbing where none exists as a separate line; extract fans, dryer vents and new circuits are quoted on top. Prices include VAT at 20%.

House types around Bognor Regis and what they mean for a kitchen

The housing mix across West Sussex includes 1930s semis, flint and brick cottages, post-war new town houses and seaside bungalows, so no two kitchen fits are quite alike. Crawley's new-town houses often have a compact galley, while seaside bungalows in Worthing and Bognor Regis tend to have a small square kitchen beside the dining area.

Coastal flats may have no lift, and village lanes on the edge of the Downs can be narrow for delivery lorries, so the delivery route is checked at the survey. West Sussex has mostly hard water, so limescale on taps, sinks and boiling water taps is common and a filter is worth considering.

Regulations for kitchen work in Bognor Regis

Fitting a utility room needs no planning permission in England, though a new dryer vent through the outside wall of a flat may need planning permission and the freeholder's consent. Adding sockets to an existing circuit is not notifiable, but a new circuit is, under Part P. Approved Document F sets an extract rate of about 30 litres per second for a utility room, so a new fan should be sized to meet it, and if an open-flued boiler shares the room, a Gas Safe registered engineer should carry out a spillage test once a fan is fitted.

Homes in the South Downs National Park, listed flint cottages and conservation areas such as central Chichester may need consent for a new external vent.

Tips before you start

Ask for an isolation valve on the washing machine supply that can be reached without pulling the machine out from under the worktop.
If your West Sussex home has an open-flued boiler in the utility, ask for a spillage test by a Gas Safe registered engineer once an extract fan goes in.
Before choosing a dryer for your Bognor Regis utility, check whether there is an outside wall close enough for a short, straight vent duct.
A worktop over appliances needs support at each side and a gap above the machines, so they can be slid out for servicing.

Questions about utility room fitting in Bognor Regis

How much does utility room fitting cost in Bognor Regis?

Guide prices in Bognor Regis are about £1,400 to £3,400 including VAT for fitting three to six utility units and a worktop you have bought. The final price depends on the size of the kitchen and what is moving, and is set out in an itemised written quote.

Which parts of Bognor Regis do you work in?

All of them. Our West Sussex coverage takes in the whole of Bognor Regis, including the PO21 postcode district, as well as surrounding towns such as Chichester. If you are unsure, send us your postcode.

Can a worktop go over a washing machine and dryer?

Yes, and it is one of the most common utility layouts. The worktop is supported by units, end panels or a rail at each side rather than resting on the machines, with a small gap above them for vibration and so they can be slid out for servicing. Standard front-loading machines usually fit under a standard-height worktop, but we check the appliance heights against the plan first.

Can a utility room go in a garage or under the stairs?

Often, yes, as long as the space already exists and is usable. In a garage it needs to be dry and protected from frost, with power and a route for water and waste. Under the stairs, check the headroom, the ventilation and whether a door can open fully. We fit units and connect appliances in existing spaces; converting a garage into a habitable room is a separate building project.

Does a condenser or heat pump dryer need an outside vent?

No. Condenser and heat pump dryers do not need an outside vent, so they can go where a vented dryer cannot. They collect water in a container that has to be emptied, or they can be connected to the waste so they drain automatically, which is easy when the dryer sits beside the washing machine. They still give off some warmth, so the space needs air around it. A vented dryer needs a duct to an outside wall.

Utility room fitting in neighbouring towns

We also carry out utility room fitting in these towns near Bognor Regis: