Flat-pack kitchen fitting in Pimlico

Is flat-pack kitchen fitting right for your Pimlico kitchen?

If you have bought a flat-pack kitchen for your Pimlico home to keep costs down, careful assembly makes sure that saving never shows in the finished kitchen.

First-time buyers in Pimlico often choose a flat-pack range to replace a worn kitchen soon after moving in, keeping money aside for flooring and decorating. Homes right across Pimlico are covered, as are nearby places such as Westminster, Battersea and the villages in between.

What does the job involve?

The exact scope is agreed after the survey, but a typical job in Pimlico covers:

Laminate worktops cut and jointed, with cut edges sealed around the sink
Base units levelled on adjustable legs and fixed to the wall and to each other
Panels, plinths, sink, tap and appliance connections to existing points
Wall units hung on hanging rails or brackets fixed securely into the wall
Carcasses assembled on site on a flat surface and checked for square
Free survey visit to check the plan, the boxes and the room

What should you budget for flat-pack kitchen fitting in Pimlico?

As a starting point for Pimlico, these ranges include VAT at 20% and allow for typical labour costs in London. Expect costs in London to sit somewhat above UK averages, reflecting local labour rates.

What should you budget for flat-pack kitchen fitting in Pimlico?
Typical project	Guide price
Small flat-pack kitchen, built and fittedCarcasses assembled on site, then fitted as a rigid kitchen would be	£2,300–£3,900
Medium flat-pack kitchen, built and fittedAs above	£3,600–£5,500
Large flat-pack kitchen with tall units, built and fittedAs above	£5,200–£7,200

Flat-pack prices include assembling the carcasses on site and fitting units, doors, panels, plinths and laminate worktops with connections to existing points; stone worktops, new circuits, moved services, tiling and flooring are extra. Prices include VAT at 20%.

Fitting kitchens in older and newer Pimlico homes

In and around Pimlico, homes range across Victorian and Edwardian terraces, conversion flats, mansion block flats and 1930s semis. Victorian terraces often have a narrow galley beside the side return, while conversion flats and mansion blocks usually fit the kitchen into a small room or along one living-room wall.

London's mains water is hard, so limescale builds quickly on taps and boiling water taps, and a scale-reducing filter is worth planning in. Permit parking, red routes and flats without lifts are common, so parking suspensions, stair carries and lift bookings may need arranging before delivery day.

Building regulations, electrics and gas in Pimlico

Assembling and fitting a flat-pack kitchen needs no planning permission in England; if the building is listed, listed building consent may be needed where the work affects its character. Electrics must meet BS 7671: extra sockets or spurs on an existing kitchen circuit are not notifiable, but a new cooker or induction circuit is notifiable under Part P. Gas hobs are connected only by Gas Safe registered engineers, and any new cooker hood should meet Approved Document F.

Conservation areas are widespread across London, so a new extractor vent on a front wall may need permission, and leaseholders usually need the freeholder's written consent first.

Worth knowing before the fit

Stack flat-pack boxes flat on a level floor rather than on end, so that long side panels do not bow before they are assembled.
If you are building some units yourself before the fit, leave the back panels and hinges for us to check before anything is fixed to the wall.
Set aside a room next to the kitchen in your Pimlico home for assembly, with enough floor space to lay a tall larder carcass down flat.
Ask whether a sink base mat is included, and make sure every cut edge around the sink, waste and pipe holes is sealed.

Questions about flat-pack kitchen fitting in Pimlico

How much does flat-pack kitchen fitting cost in Pimlico?

For a small flat-pack kitchen, built and fitted, budget around £2,300 to £3,900 including VAT in Pimlico. That reflects typical costs in London; we confirm the actual figure in writing once we have measured up.

Do you cover all of Pimlico?

Yes. We work across Pimlico, including the SW1 postcode district, and nearby towns such as Westminster and Battersea. Book a free survey visit and we will arrange a time that suits you.

How do you protect a flat-pack sink unit from water?

Mainly by sealing. Cut edges of board near the sink, including the holes for pipes and the waste, are sealed before the unit is fitted, and the worktop cut-out is sealed before the sink goes in. A sink base mat adds a second layer of protection against drips. Isolation valves on the supplies also mean that a later leak can be shut off quickly.

Can you fit a flat-pack kitchen I have already started building?

Yes, usually. We check any carcasses you have assembled for square, tight joints and properly fitted back panels before they are used, and rebuild any that are not right. Units built in another room are moved carefully, as a carcass without its worktop and wall fixings is easy to twist out of shape. We look at them on the survey and price the work accordingly.

What is the difference between flat-pack and rigid kitchen units?

Rigid units arrive factory-assembled, usually glued and dowelled, so they are ready to fix. Flat-pack units arrive as boards and fittings in a box and are built on site. Both can make a good kitchen. Flat-pack is cheaper to buy and easier to carry into tight spaces, while rigid units save assembly time and come square from the factory, which is why the fitting labour is a little lower.

Also covering nearby towns

Neighbouring towns where we offer flat-pack kitchen fitting: