Utility room fitting in Crewe

When does utility room fitting make sense in Crewe?

When a new kitchen is being planned in Cheshire, moving the laundry to a utility often makes room for deep drawers or a dishwasher in the kitchen itself.

If the kitchen in your Cheshire home is a narrow galley, a separate utility can take the appliances that would otherwise crowd the worktop and storage. We cover all of Crewe, including the CW1 postcode district, and travel out to neighbouring towns across Cheshire.

What is in a typical job?

After the survey visit we write the scope down. For utility room fitting in Crewe it usually covers:

Free survey visit to check water, waste, power and outside wall positions
Utility sink and tap plumbed in, with new supplies and waste where none exist
Extract fan fitted to clear moisture from washing and drying
Washing machine supply, waste and isolation valve, tested for leaks
Worktop over the washing machine and dryer, supported clear of the appliances
Stacking kit fitted where the washer and dryer sit one above the other

What does utility room fitting cost in Crewe?

As a starting point for Crewe, these ranges include VAT at 20% and allow for typical labour costs in the North West. Labour rates in the North West are generally lower than in London and the South East, so these ranges are a little below the national guide.

What does utility room fitting cost in Crewe?
Typical project	Guide price
Utility units and worktop fitted (fit only)Three to six units, laminate worktop, panels	£1,100–£2,800
Utility room supplied and fittedUnits, worktop, sink, washer and dryer connections	£2,800–£6,600
New utility plumbing for a sink and washing machineSupplies, waste and valves where none exist	£380–£950

Fit-only and supply-and-fit ranges cover units, worktop and standard sink and appliance connections, with new plumbing where none exists as a separate line; extract fans, dryer vents and new circuits are quoted on top. Prices include VAT at 20%.

What kind of kitchens do we fit in Crewe?

Typical homes in this part of Cheshire include Victorian terraces, 1930s semis, new-build estates and period farmhouses and cottages. Terraces in towns such as Crewe and Warrington often have a back-addition galley, while 1930s semis usually have a small kitchen that can be opened into a dining room.

Hardness varies across Cheshire, from fairly soft in some places to moderately hard in others, so check with your supplier before choosing a filter or boiling water tap. Rural lanes and long farm drives can be awkward for delivery vans, and terraced streets in older town centres may have limited parking close to the door.

Regulations for kitchen work in Crewe

Fitting a utility room needs no planning permission in England, though a new dryer vent through the outside wall of a flat may need planning permission and the freeholder's consent. Adding sockets to an existing circuit is not notifiable, but a new circuit is, under Part P. Approved Document F sets an extract rate of about 30 litres per second for a utility room, so a new fan should be sized to meet it, and if an open-flued boiler shares the room, a Gas Safe registered engineer should carry out a spillage test once a fan is fitted.

Listed timber-framed buildings, homes in conservation areas such as central Chester and the Cheshire fringe of the Peak District National Park may need consent for new vents.

Worth knowing before the fit

Ask for an isolation valve on the washing machine supply that can be reached without pulling the machine out from under the worktop.
If your Cheshire home has an open-flued boiler in the utility, ask for a spillage test by a Gas Safe registered engineer once an extract fan goes in.
Plan the sockets in your Crewe utility so each appliance can be switched off at an accessible switch without moving the machine.
Check which dryer you have: a vented dryer needs a duct to an outside wall, while condenser and heat pump dryers need emptying or a drain.

Questions about utility room fitting in Crewe

How much does utility room fitting cost in Crewe?

For fitting three to six utility units and a worktop you have bought, budget around £1,100 to £2,800 including VAT in Crewe. That reflects typical costs in the North West; we confirm the actual figure in writing once we have measured up.

Do you work near Crewe as well?

Yes. As well as Crewe itself, we cover the rest of Cheshire and nearby towns such as Nantwich and Sandbach. The process is the same wherever the kitchen is.

Can a utility room go in a garage or under the stairs?

Often, yes, as long as the space already exists and is usable. In a garage it needs to be dry and protected from frost, with power and a route for water and waste. Under the stairs, check the headroom, the ventilation and whether a door can open fully. We fit units and connect appliances in existing spaces; converting a garage into a habitable room is a separate building project.

Does a condenser or heat pump dryer need an outside vent?

No. Condenser and heat pump dryers do not need an outside vent, so they can go where a vented dryer cannot. They collect water in a container that has to be emptied, or they can be connected to the waste so they drain automatically, which is easy when the dryer sits beside the washing machine. They still give off some warmth, so the space needs air around it. A vented dryer needs a duct to an outside wall.

Can a worktop go over a washing machine and dryer?

Yes, and it is one of the most common utility layouts. The worktop is supported by units, end panels or a rail at each side rather than resting on the machines, with a small gap above them for vibration and so they can be slid out for servicing. Standard front-loading machines usually fit under a standard-height worktop, but we check the appliance heights against the plan first.

Utility room fitting near Crewe

Neighbouring towns where we offer utility room fitting: