Utility room fitting in Nantwich

Why utility room fitting for a Nantwich home?

Families in Nantwich often want the washing machine out of the kitchen, so the noise, the wet laundry and the drying racks have a room of their own.

When a new kitchen is being planned in Cheshire, moving the laundry to a utility often makes room for deep drawers or a dishwasher in the kitchen itself. We cover all of Nantwich, including the CW5 postcode district, and travel out to neighbouring towns across Cheshire.

What is included in the work?

After the survey visit we write the scope down. For utility room fitting in Nantwich it usually covers:

Extract fan fitted to clear moisture from washing and drying
Free survey visit to check water, waste, power and outside wall positions
Utility sink and tap plumbed in, with new supplies and waste where none exist
Base, wall and tall units fitted, levelled and fixed to the wall
A vent to outside for a vented dryer, or a drain hose for condenser models
Washing machine supply, waste and isolation valve, tested for leaks

Utility room fitting prices in Nantwich

These guide ranges include VAT at 20% and are adjusted for prices in the North West. We confirm your price in writing after a free survey visit. Labour rates in the North West are generally lower than in London and the South East, so these ranges are a little below the national guide.

Utility room fitting prices in Nantwich
Typical project	Guide price
Utility units and worktop fitted (fit only)Three to six units, laminate worktop, panels	£1,100–£2,800
Utility room supplied and fittedUnits, worktop, sink, washer and dryer connections	£2,800–£6,600
New utility plumbing for a sink and washing machineSupplies, waste and valves where none exist	£380–£950

Fit-only and supply-and-fit ranges cover units, worktop and standard sink and appliance connections, with new plumbing where none exists as a separate line; extract fans, dryer vents and new circuits are quoted on top. Prices include VAT at 20%.

Kitchens in homes around Nantwich

The housing mix across Cheshire includes Victorian terraces, 1930s semis, new-build estates and period farmhouses and cottages, so no two kitchen fits are quite alike. Terraces in towns such as Crewe and Warrington often have a back-addition galley, while 1930s semis usually have a small kitchen that can be opened into a dining room.

Rural lanes and long farm drives can be awkward for delivery vans, and terraced streets in older town centres may have limited parking close to the door. Hardness varies across Cheshire, from fairly soft in some places to moderately hard in others, so check with your supplier before choosing a filter or boiling water tap.

Regulations for kitchen work in Nantwich

Fitting a utility room needs no planning permission in England, though a new dryer vent through the outside wall of a flat may need planning permission and the freeholder's consent. Adding sockets to an existing circuit is not notifiable, but a new circuit is, under Part P. Approved Document F sets an extract rate of about 30 litres per second for a utility room, so a new fan should be sized to meet it, and if an open-flued boiler shares the room, a Gas Safe registered engineer should carry out a spillage test once a fan is fitted.

Listed timber-framed buildings, homes in conservation areas such as central Chester and the Cheshire fringe of the Peak District National Park may need consent for new vents.

Practical advice for Nantwich homeowners

Plan the sockets in your Nantwich utility so each appliance can be switched off at an accessible switch without moving the machine.
Measure the washer and dryer heights, including any stacking kit, before ordering wall units or shelves to go above them.
In a Nantwich flat, check with the freeholder before a new dryer vent or extract fan is cut through an outside wall.
A worktop over appliances needs support at each side and a gap above the machines, so they can be slid out for servicing.

Questions about utility room fitting in Nantwich

How much does utility room fitting cost in Nantwich?

For fitting three to six utility units and a worktop you have bought, budget around £1,100 to £2,800 including VAT in Nantwich. That reflects typical costs in the North West; we confirm the actual figure in writing once we have measured up.

Do you cover all of Nantwich?

Yes. We work across Nantwich, including the CW5 postcode district, and nearby towns such as Crewe and Sandbach. Book a free survey visit and we will arrange a time that suits you.

Does a condenser or heat pump dryer need an outside vent?

No. Condenser and heat pump dryers do not need an outside vent, so they can go where a vented dryer cannot. They collect water in a container that has to be emptied, or they can be connected to the waste so they drain automatically, which is easy when the dryer sits beside the washing machine. They still give off some warmth, so the space needs air around it. A vented dryer needs a duct to an outside wall.

Does a utility room need an extractor fan?

Yes, in most cases. Washing and drying put a lot of moisture into a small space, so extract ventilation is strongly advised: Approved Document F sets a rate of about 30 litres per second for utility rooms in England and Wales, and the building standards in Scotland and Technical Booklet K in Northern Ireland cover ventilation too. An extract fan ducted outside is the usual answer, with a window helping but not replacing it. A vented dryer needs its own duct as well.

Can a utility room go in a garage or under the stairs?

Often, yes, as long as the space already exists and is usable. In a garage it needs to be dry and protected from frost, with power and a route for water and waste. Under the stairs, check the headroom, the ventilation and whether a door can open fully. We fit units and connect appliances in existing spaces; converting a garage into a habitable room is a separate building project.

Also covering nearby towns

The same service is available a short drive from Nantwich, including: