Sink and tap installation in Mitcham

Who usually needs sink and tap installation in Mitcham?

Some Mitcham households choose a deep ceramic farmhouse-style sink for a new kitchen and need the base unit and worktop planned around its weight and size.

Landlords in Greater London often swap tired sinks and taps between tenancies, choosing hard-wearing finishes and accessible valves so that later repairs are quick and cheap. We work throughout Mitcham (CR4) and across the wider Greater London area.

What is included in the work?

Your written quote lists everything included. For sink and tap installation, that normally means:

Waste, overflow and trap fitted, with dishwasher and washing machine waste connections
Isolation valves on the hot and cold supplies, with flexible tap tails connected
Boiling water tap fitted with its tank, filter and power supply in the cupboard
Sink moved to a new position with new supply and waste runs
Inset sink cut-outs made on site in laminate and wood worktops
Every joint leak tested, with water flow and drainage checked before handover

What does sink and tap installation cost in Mitcham?

The figures below are guide prices for Mitcham, including VAT and adjusted for typical costs across London. The fixed price comes after we have measured up. Prices in London usually run above the national guide, mainly because labour and parking cost more.

What does sink and tap installation cost in Mitcham?
Typical project	Guide price
Sink and tap plumbed inIsolation valves, waste and trap	£260–£520
Boiling water tap installedTank under the sink, filter and power supply	£200–£460
Sink moved to a new positionNew supplies and waste run	£520–£1,300
Undermount sink in a stone worktopCut-out and polishing are done by the stone fabricator	Priced with the worktop

Guide ranges cover labour and fittings such as valves, tails and wastes; the sink and tap themselves are extra, and undermount cut-outs in stone are priced with the worktop by the fabricator. Prices include VAT at 20%.

Kitchens in homes around Mitcham

The housing mix across Greater London includes Victorian and Edwardian terraces, conversion flats, mansion block flats and 1930s semis, so no two kitchen fits are quite alike. Victorian terraces often have a narrow galley beside the side return, while conversion flats and mansion blocks usually fit the kitchen into a small room or along one living-room wall.

Permit parking, red routes and flats without lifts are common, so parking suspensions, stair carries and lift bookings may need arranging before delivery day. London's mains water is hard, so limescale builds quickly on taps and boiling water taps, and a scale-reducing filter is worth planning in.

Do you need approval for sink and tap installation in Mitcham?

Replacing a sink and tap needs no approval in England, but the plumbing should meet the Water Supply (Water Fittings) Regulations 1999, including isolation valves and backflow protection. Connecting to an existing waste is routine, while a new connection to an underground drain involves building control. A new spur for a boiling water tap on an existing kitchen circuit is not notifiable under Part P, but it must meet BS 7671.

Conservation areas are widespread across London, so a new extractor vent on a front wall may need permission, and leaseholders usually need the freeholder's written consent first.

Getting the most from your sink and tap installation

Ask for the dishwasher and washing machine hoses to be routed so they cannot kink behind the units once the appliances are pushed back into place.
Find the stopcock in your Mitcham home before the plumber arrives and check it turns off fully, as older stopcocks can stick or let water past.
Check the tap's hole size against the sink or worktop before ordering, as some taps need a larger hole than an existing sink provides.
If a dishwasher or washing machine sits next to the sink, plan their waste connections and the trap layout together with the sink.

Questions about sink and tap installation in Mitcham

How much does sink and tap installation cost in Mitcham?

For plumbing in a new sink and tap, budget around £260 to £520 including VAT in Mitcham. That reflects typical costs in London; we confirm the actual figure in writing once we have measured up.

Do you cover all of Mitcham?

Yes. We work across Mitcham, including the CR4 postcode district, and nearby towns such as Morden and Tooting. Book a free survey visit and we will arrange a time that suits you.

Can a dishwasher and washing machine drain through the sink waste?

Yes, in most kitchens. The sink trap can take an appliance connection on a spigot, or a separate standpipe can be fitted. The appliance hose needs to rise to the height its manufacturer specifies before it drops to the waste, so dirty water cannot siphon back. Two appliances can usually share a double-spigot trap, which we plan with the sink.

Do I need isolation valves under my kitchen sink?

They are strongly advised, and we fit them as standard. An isolation valve on each supply to the tap, and on each appliance supply, lets you turn off the water to one fitting without shutting off the whole house. That makes changing a tap cartridge or dealing with a leak far simpler. The valves are left where they can still be reached once the cupboard is in use.

What is the difference between an inset and an undermount sink?

An inset sink drops into a cut-out from above, with its rim resting on the worktop, and suits laminate, wood and stone. An undermount sink is fixed beneath the worktop so the edge of the cut-out is exposed, which usually calls for a solid, water-resistant material such as stone or solid surface. Undermount cut-outs in stone are cut and polished by the fabricator.

Sink and tap installation in neighbouring towns

Neighbouring towns where we offer sink and tap installation: