Hob and oven installation in Dundee

Who usually needs hob and oven installation in Dundee?

Keen cooks across Dundee and Angus often choose a range cooker, which needs a level floor, the right clearances to the units and a stability bracket on gas models.

Many households in Dundee switch from gas to induction when they refit, which can mean a new cooker circuit and the old gas supply capped off safely. Homes right across Dundee are covered, as are nearby places such as St Andrews, Forfar and the villages in between.

What we cover for hob and oven installation in Dundee

The exact scope is agreed after the survey, but a typical job in Dundee covers:

Induction and ceramic hobs wired to a suitable cooker circuit and tested
Appliance models checked against worktop cut-outs, oven housings and existing supplies
Gas hobs and cookers connected and tightness tested by a Gas Safe registered engineer
Gas supply moved to a new hob position, with pipework tested and made good
Range cookers levelled, with a stability bracket fitted to gas and dual-fuel models
Old hob or oven disconnected safely and taken away for recycling

What should you budget for hob and oven installation in Dundee?

Typical hob and oven installation prices for homes in Dundee, including VAT and adjusted for Scotland. Your own figure depends on the size of the kitchen, the layout and what is moving. Labour rates in Scotland are generally lower than in London and the South East, so these ranges are a little below the national guide.

What should you budget for hob and oven installation in Dundee?
Typical project	Guide price
Gas hob fitted and connected by a Gas Safe registered engineerExisting gas supply in the right place, tightness tested	£110–£280
Induction or ceramic hob fitted on a suitable circuitCut-out, connection and test	£110–£240
Range cooker installedGas or dual fuel, levelled, stability bracket fitted	£140–£380
New gas pipe run to a new hob positionPipework, testing and making good	£240–£750

Guide ranges cover fitting and connection to an existing suitable gas supply or cooker circuit, except the new gas pipe row; a new cooker circuit, alterations to stone worktops and the appliances themselves are priced separately. Prices include VAT at 20%.

Kitchens in homes around Dundee

Across Dundee and Angus you will often find sandstone tenement flats, Victorian villas, post-war council-built houses and fishing town cottages, and each shapes the kitchen differently. Dundee's tenement flats often have a narrow kitchen or a box room off the hall, while villas in Broughty Ferry and the Angus towns tend to have larger separate kitchens.

Common stairs in tenements, steep streets in parts of Dundee and narrow glen roads in Angus can each affect deliveries and worktop lengths. Dundee and Angus have soft mains water, so limescale is rarely an issue and taps and boiling water taps tend to stay free of heavy scale.

Building regulations, electrics and gas in Dundee

In Scotland, gas hobs, cookers and pipework must be fitted and tested by a Gas Safe registered engineer. Replacing a hob or oven, or adding a cooker circuit in a house, does not normally need a building warrant, but the electrics must meet building standards 4.5 and 4.6 and BS 7671. Ask for an Electrical Installation Certificate for any new circuit.

Consent may be needed for new vents on listed buildings and in conservation areas, and homes in the upper Angus glens fall within the Cairngorms National Park.

Planning ahead

If you are moving the hob in your Dundee kitchen, choose the cooker hood at the same time so the extraction and ducting can follow it.
Measure the gap for a range cooker at worktop height and at floor level, as older walls and thick skirting can narrow the space more than expected.
If you are replacing an old cooker with a separate hob and oven in your Dundee kitchen, ask for the gas supply position and condition to be checked first.
Check the induction hob's power rating against your existing cooker circuit, as induction hobs often need a dedicated circuit from the consumer unit.

Questions about hob and oven installation in Dundee

How much does hob and oven installation cost in Dundee?

For connecting a gas hob to an existing supply, budget around £110 to £280 including VAT in Dundee. That reflects typical costs in Scotland; we confirm the actual figure in writing once we have measured up.

Do you cover all of Dundee?

Yes. We work across Dundee, including the DD1 postcode district, and nearby towns such as St Andrews and Forfar. Book a free survey visit and we will arrange a time that suits you.

Who is allowed to connect a gas hob?

By law, anyone who carries out gas work for payment must be on the Gas Safe Register, in Great Britain and Northern Ireland, and anyone working on gas must be competent to do it. We only use Gas Safe registered engineers, and we strongly advise against fitting a gas hob yourself. The engineer connects the hob, tests the installation for tightness, checks the burners and the room's ventilation, and leaves the appliance safe to use. You can ask to see the engineer's Gas Safe ID card before work starts.

Do built-in ovens need ventilation?

Yes. Built-in ovens release heat, and their installation instructions set the gaps and openings the housing must leave, often at the back or beneath the oven. Blocking them can overheat the surrounding units and the oven's own controls. An oven under the worktop and one in a tall housing have different requirements, so we check the instructions for your model before fitting.

Why does a range cooker need a stability bracket?

Because a range cooker can tip forward if weight is put on an open oven door, which could damage the gas connection or injure someone. Gas and dual-fuel models are secured with a stability bracket or chain to the wall or floor behind, as the manufacturer specifies, and the cooker is levelled on a firm floor so its doors close properly and pans sit flat.

Hob and oven installation near Dundee

Neighbouring towns where we offer hob and oven installation: