Cooker hood installation · Scotland
Cooker hood installation in Perth and Kinross
Our cooker hood installation work covers the whole of Perth and Kinross, including Perth, Crieff and Fife.
Thinking about cooker hood installation in Perth and Kinross?
Some Perth and Kinross households simply want a quieter, more effective hood after years of a noisy one that barely clears the steam above a busy family hob.
If your Perth and Kinross kitchen has an older open-flued boiler, fitting a stronger hood needs care, as it can affect the flue and should be followed by a spillage test.
What does cooker hood installation in Perth and Kinross include?
Your written quote lists everything included. For cooker hood installation, that normally means:
- Survey of the hob position, duct route, outside wall and any open-flued appliance
- Hood fixed at the height set by the hood and hob manufacturers
- Core drilling through the outside wall and an external grille fitted and sealed
- Short, straight runs of rigid ducting wherever the route allows
- Island and ceiling hoods fixed into the ceiling structure by two people
- Recirculating hoods fitted with carbon filters, and their limits explained
- Power supply connected by an electrician and tested to BS 7671
- Spillage test by a Gas Safe registered engineer where an open-flued appliance is present
How much does cooker hood installation cost in Perth and Kinross?
The figures below are guide prices for Perth and Kinross, including VAT and adjusted for typical costs across Scotland. The fixed price comes after we have measured up. Prices in Scotland usually come in below the national guide, as labour rates are lower than in the South East.
| Typical project | Guide price |
|---|---|
| Like-for-like cooker hood swapSame position and ducting | £110–£230 |
| New ducted hood through an outside wallCore drilling, ducting run and external grille | £280–£850 |
| Island or ceiling hood installedTwo-person install, fixings to the ceiling structure | £280–£590 |
| Recirculating hood fittedNo ducting; carbon filters need replacing | £110–£280 |
Guide ranges cover fitting and connection with standard ducting through a straightforward wall; long or concealed duct runs, ceiling repairs, new electrical spurs, spillage tests and the hood itself are priced separately. Prices include VAT at 20%.
Kitchens in homes across Perth and Kinross
You will find sandstone tenement flats, Victorian villas, stone cottages and post-war council-built houses throughout Perth and Kinross. Victorian villas in Perth and Crieff often have a separate kitchen and former scullery, while tenement flats tend to have a small kitchen off the hall.
Mains water across Perth and Kinross is soft, though some remote homes rely on private supplies that may need testing and filtering. Highland Perthshire roads can be narrow and winding, and older town streets may have limited parking, so delivery vehicle size and timing are planned ahead.
Joining a villa kitchen and old scullery into one room is a common project, with a building warrant needed if a load-bearing wall is involved. Rural cottages are often off the gas grid and suit induction cooking or an oil-fired range.
Rules for cooker hood installation in Perth and Kinross
In Scotland, standard 3.14 of the domestic Technical Handbook expects kitchens to have extract ventilation, and a recirculating hood alone does not remove moisture. Fitting an extractor fan or a ducted hood does not normally need a building warrant. In a flat, a new vent through a shared outside wall may need the other owners' agreement and planning permission, and a listed building may need listed building consent. Where the room has an open-flued gas appliance, a Gas Safe registered engineer should carry out a spillage test after the hood is fitted.
Parts of highland Perthshire lie within the Cairngorms or Loch Lomond and The Trossachs national parks, and listed buildings elsewhere may need consent for new vents.
Before you start
- Keep the duct run short and straight with rigid ducting, because every bend and extra metre of flexible hose reduces how much air the hood moves.
- Choose ducted extraction where you can; a recirculating hood filters grease and smells but leaves the moisture from cooking in the room.
- If the kitchen has an open-flued boiler or gas fire, a Gas Safe registered engineer should carry out a spillage test after the hood is fitted.
- Check the minimum height above the hob in both the hood and hob instructions, and use the greater of the two figures.
- Ask for rigid ducting rather than flexible hose wherever the route allows, as it moves more air, gathers less grease and is usually quieter.
- Replace the carbon filters in a recirculating hood as often as the manufacturer advises, and clean the grease filters regularly so the hood keeps working well.
Questions about cooker hood installation in Perth and Kinross
How much does cooker hood installation cost in Perth and Kinross?
Guide prices in Perth and Kinross are about £110 to £230 including VAT for a like-for-like cooker hood swap. The final price depends on the size of the kitchen and what is moving, and is set out in an itemised written quote.
Do you cover the whole of Perth and Kinross?
Yes. We carry out cooker hood installation across Perth and Kinross, including Perth and Crieff. Every job starts with a free survey visit and an itemised written quote.
Why might a cooker hood need a spillage test?
Because a hood pulling air out of a room can draw fumes back down the flue of an open-flued gas appliance, such as some older boilers or gas fires. Where the kitchen, or a room open to it, has one, a Gas Safe registered engineer should carry out a spillage test with the hood running at full speed. Room-sealed boilers are not affected in the same way.
Does a cooker hood need a hole in the wall?
A ducted hood does. The usual route is a core-drilled hole through the nearest outside wall, with rigid ducting from the hood and an external grille sealed into the wall. Where the hob is far from an outside wall, the duct can sometimes run above the wall units or through a ceiling void. A recirculating hood needs no hole, but it removes no moisture.
How high should a cooker hood be above the hob?
At least the minimum distance given by the manufacturers. Both the hood and the hob instructions set a minimum gap between them, and where they differ the greater figure should be used. Gas hobs usually need more clearance than induction. A hood fitted too low is a fire risk, while one fitted much higher than recommended captures less steam.
Cooker hood installation in towns across Perth and Kinross
Choose a town for local guide prices and postcode coverage: