Utility room fitting · England
Utility room fitting in Wiltshire
We carry out utility room fitting across Wiltshire, from Swindon to the smaller towns, with a free survey visit and an itemised written quote as standard.
When does utility room fitting make sense in Wiltshire?
If the kitchen in your Wiltshire home is a narrow galley, a separate utility can take the appliances that would otherwise crowd the worktop and storage.
Landlords letting larger family homes across Wiltshire sometimes add a utility so tenants have room for laundry, coats and cleaning kit without filling the kitchen with appliances.
What does utility room fitting in Wiltshire include?
After the survey visit we write the scope down. For utility room fitting in Wiltshire it usually covers:
- Free survey visit to check water, waste, power and outside wall positions
- Base, wall and tall units fitted, levelled and fixed to the wall
- Worktop over the washing machine and dryer, supported clear of the appliances
- Washing machine supply, waste and isolation valve, tested for leaks
- A vent to outside for a vented dryer, or a drain hose for condenser models
- Stacking kit fitted where the washer and dryer sit one above the other
- Utility sink and tap plumbed in, with new supplies and waste where none exist
- Extract fan fitted to clear moisture from washing and drying
How much does utility room fitting cost in Wiltshire?
As a starting point for Wiltshire, these ranges include VAT at 20% and allow for typical labour costs in the South West. For the South West, these ranges are close to the national figures.
| Typical project | Guide price |
|---|---|
| Utility units and worktop fitted (fit only)Three to six units, laminate worktop, panels | £1,200–£3,100 |
| Utility room supplied and fittedUnits, worktop, sink, washer and dryer connections | £3,100–£7,200 |
| New utility plumbing for a sink and washing machineSupplies, waste and valves where none exist | £410–£1,000 |
Fit-only and supply-and-fit ranges cover units, worktop and standard sink and appliance connections, with new plumbing where none exists as a separate line; extract fans, dryer vents and new circuits are quoted on top. Prices include VAT at 20%.
Kitchens in homes across Wiltshire
The housing mix across Wiltshire includes thatched and stone cottages, Victorian railway terraces, post-war estate houses and new-build estates, so no two kitchen fits are quite alike. Railway terraces in Swindon often have a narrow back kitchen, while stone and thatched cottages in the villages tend to have small kitchens with low ceilings.
Wiltshire's water is hard, much of it from chalk, so limescale on taps and boiling water taps is common and a filter can help. Village lanes and farm tracks can be narrow for delivery lorries, and Salisbury's historic centre has limited parking, so delivery is planned in advance.
Railway terraces often have a narrow galley that owners open into the dining room to make a family kitchen. In a thatched or stone cottage, uneven walls and floors usually mean careful scribing, and cooker extraction needs extra thought where a vent cannot easily go through a thick or listed wall.
Rules for utility room fitting in Wiltshire
Fitting a utility room needs no planning permission in England, though a new dryer vent through the outside wall of a flat may need planning permission and the freeholder's consent. Adding sockets to an existing circuit is not notifiable, but a new circuit is, under Part P. Approved Document F sets an extract rate of about 30 litres per second for a utility room, so a new fan should be sized to meet it, and if an open-flued boiler shares the room, a Gas Safe registered engineer should carry out a spillage test once a fan is fitted.
Listed thatched cottages, Salisbury's historic centre and other conservation areas may need consent for a new external vent or changes to historic features.
Before you start
- A utility in a garage needs to be dry, lit and kept above freezing already; converting the garage itself is a separate building job.
- Check which dryer you have: a vented dryer needs a duct to an outside wall, while condenser and heat pump dryers need emptying or a drain.
- A worktop over appliances needs support at each side and a gap above the machines, so they can be slid out for servicing.
- Under-stairs spaces can take a washer and dryer, but check the headroom, the ventilation and room to pull machines out before committing.
- If your Wiltshire home has an open-flued boiler in the utility, ask for a spillage test by a Gas Safe registered engineer once an extract fan goes in.
- If the utility will be in the garage of your Wiltshire home, make sure the space stays above freezing in winter for the pipes and machines.
Questions about utility room fitting in Wiltshire
How much does utility room fitting cost in Wiltshire?
Utility room fitting in Wiltshire typically costs £1,200 to £3,100 including VAT for fitting three to six utility units and a worktop you have bought, based on prices in the South West. Larger or more involved jobs cost more, and your price is fixed in writing after a free survey visit.
Do you cover the whole of Wiltshire?
Yes. We carry out utility room fitting across Wiltshire, including Swindon, Salisbury, Trowbridge and Chippenham. Every job starts with a free survey visit and an itemised written quote.
Does a utility room need an extractor fan?
Yes, in most cases. Washing and drying put a lot of moisture into a small space, so extract ventilation is strongly advised: Approved Document F sets a rate of about 30 litres per second for utility rooms in England and Wales, and the building standards in Scotland and Technical Booklet K in Northern Ireland cover ventilation too. An extract fan ducted outside is the usual answer, with a window helping but not replacing it. A vented dryer needs its own duct as well.
Can a utility room go in a garage or under the stairs?
Often, yes, as long as the space already exists and is usable. In a garage it needs to be dry and protected from frost, with power and a route for water and waste. Under the stairs, check the headroom, the ventilation and whether a door can open fully. We fit units and connect appliances in existing spaces; converting a garage into a habitable room is a separate building project.
Can a worktop go over a washing machine and dryer?
Yes, and it is one of the most common utility layouts. The worktop is supported by units, end panels or a rail at each side rather than resting on the machines, with a small gap above them for vibration and so they can be slid out for servicing. Standard front-loading machines usually fit under a standard-height worktop, but we check the appliance heights against the plan first.
Utility room fitting in towns across Wiltshire
Choose a town for local guide prices and postcode coverage:
- Utility room fitting in Swindon
- Utility room fitting in Salisbury
- Utility room fitting in Trowbridge
- Utility room fitting in Chippenham
- Utility room fitting in Melksham
- Utility room fitting in Warminster
- Utility room fitting in Devizes
- Utility room fitting in Marlborough
- Utility room fitting in Malmesbury