Utility room fitting in St Austell

Why do people in St Austell choose utility room fitting?

In a St Austell house where the garage is already used for storage rather than the car, some people fit a run of units and the laundry along one wall.

Landlords letting larger family homes across Cornwall sometimes add a utility so tenants have room for laundry, coats and cleaning kit without filling the kitchen with appliances. If your home is in St Austell or close by in Bodmin or Truro, the same survey, quote and fitting process applies.

What is in a typical job?

Here is what usually goes into utility room fitting, adjusted to your St Austell kitchen after we have measured it:

Stacking kit fitted where the washer and dryer sit one above the other
Extract fan fitted to clear moisture from washing and drying
Washing machine supply, waste and isolation valve, tested for leaks
Free survey visit to check water, waste, power and outside wall positions
Base, wall and tall units fitted, levelled and fixed to the wall
A vent to outside for a vented dryer, or a drain hose for condenser models

Guide prices for utility room fitting in St Austell

The figures below are guide prices for St Austell, including VAT and adjusted for typical costs across the South West. The fixed price comes after we have measured up. Prices across the South West are broadly in line with UK averages.

Guide prices for utility room fitting in St Austell
Typical project	Guide price
Utility units and worktop fitted (fit only)Three to six units, laminate worktop, panels	£1,200–£3,100
Utility room supplied and fittedUnits, worktop, sink, washer and dryer connections	£3,100–£7,200
New utility plumbing for a sink and washing machineSupplies, waste and valves where none exist	£410–£1,000

Fit-only and supply-and-fit ranges cover units, worktop and standard sink and appliance connections, with new plumbing where none exists as a separate line; extract fans, dryer vents and new circuits are quoted on top. Prices include VAT at 20%.

What kind of kitchens do we fit in St Austell?

You will find granite and slate cottages, Victorian terraces, post-war bungalows and converted barns throughout Cornwall. Older stone cottages often have a small, low-ceilinged kitchen with uneven walls, while post-war bungalows tend to have a square kitchen beside a separate dining area.

Narrow lanes, steep harbour streets and cottages with no parking outside can make delivering long worktops tricky, so delivery day needs planning in advance. Mains water across most of Cornwall is soft, which is kinder to taps and appliances, so heavy limescale build-up is rarely a problem.

What rules apply to utility room fitting in St Austell?

Fitting a utility room needs no planning permission in England, though a new dryer vent through the outside wall of a flat may need planning permission and the freeholder's consent. Adding sockets to an existing circuit is not notifiable, but a new circuit is, under Part P. Approved Document F sets an extract rate of about 30 litres per second for a utility room, so a new fan should be sized to meet it, and if an open-flued boiler shares the room, a Gas Safe registered engineer should carry out a spillage test once a fan is fitted.

Where a cottage is listed or sits in one of the many harbour-town conservation areas, consent may be needed before a new extractor vent is cut through an outside wall.

Worth knowing before the fit

If your Cornwall home has an open-flued boiler in the utility, ask for a spillage test by a Gas Safe registered engineer once an extract fan goes in.
Before choosing a dryer for your St Austell utility, check whether there is an outside wall close enough for a short, straight vent duct.
Measure the washer and dryer heights, including any stacking kit, before ordering wall units or shelves to go above them.
Stacking the dryer on the washing machine saves width, but it needs a stacking kit that suits both machines and enough height for the pair.

Questions about utility room fitting in St Austell

How much does utility room fitting cost in St Austell?

Guide prices in St Austell are about £1,200 to £3,100 including VAT for fitting three to six utility units and a worktop you have bought. The final price depends on the size of the kitchen and what is moving, and is set out in an itemised written quote.

Do you cover all of St Austell?

Yes. We work across St Austell, including the PL25 postcode district, and nearby towns such as Bodmin and Truro. Book a free survey visit and we will arrange a time that suits you.

Does a utility room need an extractor fan?

Yes, in most cases. Washing and drying put a lot of moisture into a small space, so extract ventilation is strongly advised: Approved Document F sets a rate of about 30 litres per second for utility rooms in England and Wales, and the building standards in Scotland and Technical Booklet K in Northern Ireland cover ventilation too. An extract fan ducted outside is the usual answer, with a window helping but not replacing it. A vented dryer needs its own duct as well.

Can a worktop go over a washing machine and dryer?

Yes, and it is one of the most common utility layouts. The worktop is supported by units, end panels or a rail at each side rather than resting on the machines, with a small gap above them for vibration and so they can be slid out for servicing. Standard front-loading machines usually fit under a standard-height worktop, but we check the appliance heights against the plan first.

Does a condenser or heat pump dryer need an outside vent?

No. Condenser and heat pump dryers do not need an outside vent, so they can go where a vented dryer cannot. They collect water in a container that has to be emptied, or they can be connected to the waste so they drain automatically, which is easy when the dryer sits beside the washing machine. They still give off some warmth, so the space needs air around it. A vented dryer needs a duct to an outside wall.

Also covering nearby towns

We also carry out utility room fitting in these towns near St Austell: