Utility room fitting in Truro

Why utility room fitting for a Truro home?

If your Truro home has a back lobby or a rear porch with a little spare width, a few units and a stacked washer and dryer can make it a working utility.

If the kitchen in your Cornwall home is a narrow galley, a separate utility can take the appliances that would otherwise crowd the worktop and storage. If your home is in Truro or close by in Falmouth or Redruth, the same survey, quote and fitting process applies.

What we cover for utility room fitting in Truro

Every kitchen is different, so we confirm the scope in writing. Most jobs of this kind include:

Base, wall and tall units fitted, levelled and fixed to the wall
Worktop over the washing machine and dryer, supported clear of the appliances
Utility sink and tap plumbed in, with new supplies and waste where none exist
Washing machine supply, waste and isolation valve, tested for leaks
Stacking kit fitted where the washer and dryer sit one above the other
Extract fan fitted to clear moisture from washing and drying

Guide prices for utility room fitting in Truro

These guide ranges include VAT at 20% and are adjusted for prices in the South West. We confirm your price in writing after a free survey visit. For the South West, these ranges are close to the national figures.

Guide prices for utility room fitting in Truro
Typical project	Guide price
Utility units and worktop fitted (fit only)Three to six units, laminate worktop, panels	£1,200–£3,100
Utility room supplied and fittedUnits, worktop, sink, washer and dryer connections	£3,100–£7,200
New utility plumbing for a sink and washing machineSupplies, waste and valves where none exist	£410–£1,000

Fit-only and supply-and-fit ranges cover units, worktop and standard sink and appliance connections, with new plumbing where none exists as a separate line; extract fans, dryer vents and new circuits are quoted on top. Prices include VAT at 20%.

Fitting kitchens in older and newer Truro homes

The housing mix across Cornwall includes granite and slate cottages, Victorian terraces, post-war bungalows and converted barns, so no two kitchen fits are quite alike. Older stone cottages often have a small, low-ceilinged kitchen with uneven walls, while post-war bungalows tend to have a square kitchen beside a separate dining area.

Mains water across most of Cornwall is soft, which is kinder to taps and appliances, so heavy limescale build-up is rarely a problem. Narrow lanes, steep harbour streets and cottages with no parking outside can make delivering long worktops tricky, so delivery day needs planning in advance.

Building regulations, electrics and gas in Truro

Fitting a utility room needs no planning permission in England, though a new dryer vent through the outside wall of a flat may need planning permission and the freeholder's consent. Adding sockets to an existing circuit is not notifiable, but a new circuit is, under Part P. Approved Document F sets an extract rate of about 30 litres per second for a utility room, so a new fan should be sized to meet it, and if an open-flued boiler shares the room, a Gas Safe registered engineer should carry out a spillage test once a fan is fitted.

Where a cottage is listed or sits in one of the many harbour-town conservation areas, consent may be needed before a new extractor vent is cut through an outside wall.

Practical advice for Truro homeowners

Ask for an isolation valve on the washing machine supply that can be reached without pulling the machine out from under the worktop.
Plan the sockets in your Truro utility so each appliance can be switched off at an accessible switch without moving the machine.
Before choosing a dryer for your Truro utility, check whether there is an outside wall close enough for a short, straight vent duct.
If there is no water or waste in the space, new plumbing has to reach it, which is simplest close to an existing kitchen or bathroom.

Questions about utility room fitting in Truro

How much does utility room fitting cost in Truro?

Utility room fitting in Truro typically costs £1,200 to £3,100 including VAT for fitting three to six utility units and a worktop you have bought, based on prices in the South West. Larger or more involved jobs cost more, and your price is fixed in writing after a free survey visit.

Do you cover all of Truro?

Yes. We work across Truro, including the TR1 postcode district, and nearby towns such as Falmouth and Redruth. Book a free survey visit and we will arrange a time that suits you.

Can a worktop go over a washing machine and dryer?

Yes, and it is one of the most common utility layouts. The worktop is supported by units, end panels or a rail at each side rather than resting on the machines, with a small gap above them for vibration and so they can be slid out for servicing. Standard front-loading machines usually fit under a standard-height worktop, but we check the appliance heights against the plan first.

Does a utility room need an extractor fan?

Yes, in most cases. Washing and drying put a lot of moisture into a small space, so extract ventilation is strongly advised: Approved Document F sets a rate of about 30 litres per second for utility rooms in England and Wales, and the building standards in Scotland and Technical Booklet K in Northern Ireland cover ventilation too. An extract fan ducted outside is the usual answer, with a window helping but not replacing it. A vented dryer needs its own duct as well.

Does a condenser or heat pump dryer need an outside vent?

No. Condenser and heat pump dryers do not need an outside vent, so they can go where a vented dryer cannot. They collect water in a container that has to be emptied, or they can be connected to the waste so they drain automatically, which is easy when the dryer sits beside the washing machine. They still give off some warmth, so the space needs air around it. A vented dryer needs a duct to an outside wall.

Also covering nearby towns

We also carry out utility room fitting in these towns near Truro: