Utility room fitting in Portsmouth

Thinking about utility room fitting in Portsmouth?

Families in Portsmouth often want the washing machine out of the kitchen, so the noise, the wet laundry and the drying racks have a room of their own.

Larger households in Portsmouth sharing a lot of laundry often want a stacked washer and dryer, a hanging rail and a clear worktop for folding. If your home is in Portsmouth or close by in Southsea or Gosport, the same survey, quote and fitting process applies.

What we cover for utility room fitting in Portsmouth

Your written quote lists everything included. For utility room fitting, that normally means:

Washing machine supply, waste and isolation valve, tested for leaks
Utility sink and tap plumbed in, with new supplies and waste where none exist
Free survey visit to check water, waste, power and outside wall positions
Extract fan fitted to clear moisture from washing and drying
Worktop over the washing machine and dryer, supported clear of the appliances
Base, wall and tall units fitted, levelled and fixed to the wall

What does utility room fitting cost in Portsmouth?

The figures below are guide prices for Portsmouth, including VAT and adjusted for typical costs across the South East. The fixed price comes after we have measured up. Labour in the South East generally costs more than the UK average, which lifts these ranges a little.

What does utility room fitting cost in Portsmouth?
Typical project	Guide price
Utility units and worktop fitted (fit only)Three to six units, laminate worktop, panels	£1,400–£3,400
Utility room supplied and fittedUnits, worktop, sink, washer and dryer connections	£3,400–£8,000
New utility plumbing for a sink and washing machineSupplies, waste and valves where none exist	£460–£1,200

Fit-only and supply-and-fit ranges cover units, worktop and standard sink and appliance connections, with new plumbing where none exists as a separate line; extract fans, dryer vents and new circuits are quoted on top. Prices include VAT at 20%.

Kitchens in homes around Portsmouth

The housing mix across Hampshire includes Victorian terraces, 1930s semis, post-war estate houses and thatched and brick cottages, so no two kitchen fits are quite alike. Terraces in Southampton and Portsmouth often have a narrow back kitchen, while post-war estate houses tend to have a compact rectangular room suited to an L-shape.

Dense terraced streets can be very tight for parking, and New Forest lanes and village roads may limit the size of delivery vehicle. Water across Hampshire is mostly hard, largely from chalk sources, so limescale on taps and boiling water taps is common and a filter can help.

Do you need approval for utility room fitting in Portsmouth?

Fitting a utility room needs no planning permission in England, though a new dryer vent through the outside wall of a flat may need planning permission and the freeholder's consent. Adding sockets to an existing circuit is not notifiable, but a new circuit is, under Part P. Approved Document F sets an extract rate of about 30 litres per second for a utility room, so a new fan should be sized to meet it, and if an open-flued boiler shares the room, a Gas Safe registered engineer should carry out a spillage test once a fan is fitted.

Homes within the New Forest or South Downs national parks, listed cottages and conservation areas may need consent for a new extractor vent or alterations to historic features.

Planning ahead

Measure the washer and dryer heights, including any stacking kit, before ordering wall units or shelves to go above them.
Ask for an isolation valve on the washing machine supply that can be reached without pulling the machine out from under the worktop.
Plan the sockets in your Portsmouth utility so each appliance can be switched off at an accessible switch without moving the machine.
If there is no water or waste in the space, new plumbing has to reach it, which is simplest close to an existing kitchen or bathroom.

Questions about utility room fitting in Portsmouth

How much does utility room fitting cost in Portsmouth?

Utility room fitting in Portsmouth typically costs £1,400 to £3,400 including VAT for fitting three to six utility units and a worktop you have bought, based on prices in the South East. Larger or more involved jobs cost more, and your price is fixed in writing after a free survey visit.

Do you cover all of Portsmouth?

Yes. We work across Portsmouth, including the PO5 postcode district, and nearby towns such as Southsea and Gosport. Book a free survey visit and we will arrange a time that suits you.

Can a worktop go over a washing machine and dryer?

Yes, and it is one of the most common utility layouts. The worktop is supported by units, end panels or a rail at each side rather than resting on the machines, with a small gap above them for vibration and so they can be slid out for servicing. Standard front-loading machines usually fit under a standard-height worktop, but we check the appliance heights against the plan first.

Does a utility room need an extractor fan?

Yes, in most cases. Washing and drying put a lot of moisture into a small space, so extract ventilation is strongly advised: Approved Document F sets a rate of about 30 litres per second for utility rooms in England and Wales, and the building standards in Scotland and Technical Booklet K in Northern Ireland cover ventilation too. An extract fan ducted outside is the usual answer, with a window helping but not replacing it. A vented dryer needs its own duct as well.

Can a utility room go in a garage or under the stairs?

Often, yes, as long as the space already exists and is usable. In a garage it needs to be dry and protected from frost, with power and a route for water and waste. Under the stairs, check the headroom, the ventilation and whether a door can open fully. We fit units and connect appliances in existing spaces; converting a garage into a habitable room is a separate building project.

Nearby places we cover

Close to Portsmouth? We cover these nearby towns too: