Utility room fitting in Glastonbury

Who usually needs utility room fitting in Glastonbury?

Larger households in Glastonbury sharing a lot of laundry often want a stacked washer and dryer, a hanging rail and a clear worktop for folding.

In a Glastonbury house where the garage is already used for storage rather than the car, some people fit a run of units and the laundry along one wall. Kitchens in every part of Glastonbury are covered, and the survey visit is free wherever you are in Somerset.

What is in a typical job?

Here is what usually goes into utility room fitting, adjusted to your Glastonbury kitchen after we have measured it:

Base, wall and tall units fitted, levelled and fixed to the wall
Stacking kit fitted where the washer and dryer sit one above the other
Extract fan fitted to clear moisture from washing and drying
Free survey visit to check water, waste, power and outside wall positions
A vent to outside for a vented dryer, or a drain hose for condenser models
Utility sink and tap plumbed in, with new supplies and waste where none exist

Utility room fitting prices in Glastonbury

The figures below are guide prices for Glastonbury, including VAT and adjusted for typical costs across the South West. The fixed price comes after we have measured up. For the South West, these ranges are close to the national figures.

Utility room fitting prices in Glastonbury
Typical project	Guide price
Utility units and worktop fitted (fit only)Three to six units, laminate worktop, panels	£1,200–£3,100
Utility room supplied and fittedUnits, worktop, sink, washer and dryer connections	£3,100–£7,200
New utility plumbing for a sink and washing machineSupplies, waste and valves where none exist	£410–£1,000

Fit-only and supply-and-fit ranges cover units, worktop and standard sink and appliance connections, with new plumbing where none exists as a separate line; extract fans, dryer vents and new circuits are quoted on top. Prices include VAT at 20%.

Fitting kitchens in older and newer Glastonbury homes

Across Somerset you will often find Georgian townhouses, Victorian terraces, stone cottages and post-war estate houses, and each shapes the kitchen differently. Georgian townhouses in Bath often have kitchens at lower-ground level or in flats on upper floors, while Victorian terraces in Taunton and Yeovil tend to have a narrow back galley.

Steep streets and controlled parking in Bath, upper-floor flats without lifts and narrow village lanes can each make delivering worktops slower. Somerset's mains water is mostly hard, so limescale on taps and boiling water taps is common, and a filter or softener can help keep them working well.

Do you need approval for utility room fitting in Glastonbury?

Fitting a utility room needs no planning permission in England, though a new dryer vent through the outside wall of a flat may need planning permission and the freeholder's consent. Adding sockets to an existing circuit is not notifiable, but a new circuit is, under Part P. Approved Document F sets an extract rate of about 30 litres per second for a utility room, so a new fan should be sized to meet it, and if an open-flued boiler shares the room, a Gas Safe registered engineer should carry out a spillage test once a fan is fitted.

Bath is a World Heritage city with many listed buildings, and homes in Exmoor National Park or conservation areas may need consent for new vents or internal changes.

Getting the most from your utility room fitting

Before choosing a dryer for your Glastonbury utility, check whether there is an outside wall close enough for a short, straight vent duct.
If your Somerset home has an open-flued boiler in the utility, ask for a spillage test by a Gas Safe registered engineer once an extract fan goes in.
In a Glastonbury flat, check with the freeholder before a new dryer vent or extract fan is cut through an outside wall.
If there is no water or waste in the space, new plumbing has to reach it, which is simplest close to an existing kitchen or bathroom.

Questions about utility room fitting in Glastonbury

How much does utility room fitting cost in Glastonbury?

Guide prices in Glastonbury are about £1,200 to £3,100 including VAT for fitting three to six utility units and a worktop you have bought. The final price depends on the size of the kitchen and what is moving, and is set out in an itemised written quote.

Which parts of Glastonbury do you work in?

All of them. Our Somerset coverage takes in the whole of Glastonbury, including the BA6 postcode district, as well as surrounding towns such as Wells. If you are unsure, send us your postcode.

Can a utility room go in a garage or under the stairs?

Often, yes, as long as the space already exists and is usable. In a garage it needs to be dry and protected from frost, with power and a route for water and waste. Under the stairs, check the headroom, the ventilation and whether a door can open fully. We fit units and connect appliances in existing spaces; converting a garage into a habitable room is a separate building project.

Can a worktop go over a washing machine and dryer?

Yes, and it is one of the most common utility layouts. The worktop is supported by units, end panels or a rail at each side rather than resting on the machines, with a small gap above them for vibration and so they can be slid out for servicing. Standard front-loading machines usually fit under a standard-height worktop, but we check the appliance heights against the plan first.

Does a utility room need an extractor fan?

Yes, in most cases. Washing and drying put a lot of moisture into a small space, so extract ventilation is strongly advised: Approved Document F sets a rate of about 30 litres per second for utility rooms in England and Wales, and the building standards in Scotland and Technical Booklet K in Northern Ireland cover ventilation too. An extract fan ducted outside is the usual answer, with a window helping but not replacing it. A vented dryer needs its own duct as well.

Nearby places we cover

Neighbouring towns where we offer utility room fitting: