Sink and tap installation in Putney

Thinking about sink and tap installation in Putney?

If a new dishwasher or washing machine is going next to the sink in your Putney home, the trap and waste connections usually need changing as well.

Landlords in Greater London often swap tired sinks and taps between tenancies, choosing hard-wearing finishes and accessible valves so that later repairs are quick and cheap. We cover all of Putney, including the SW15 postcode district, and travel out to neighbouring towns across Greater London.

What we cover for sink and tap installation in Putney

After the survey visit we write the scope down. For sink and tap installation in Putney it usually covers:

Every joint leak tested, with water flow and drainage checked before handover
Inset sink cut-outs made on site in laminate and wood worktops
Boiling water tap fitted with its tank, filter and power supply in the cupboard
Isolation valves on the hot and cold supplies, with flexible tap tails connected
Waste, overflow and trap fitted, with dishwasher and washing machine waste connections
Sink moved to a new position with new supply and waste runs

Sink and tap installation prices in Putney

The figures below are guide prices for Putney, including VAT and adjusted for typical costs across London. The fixed price comes after we have measured up. Expect costs in London to sit somewhat above UK averages, reflecting local labour rates.

Sink and tap installation prices in Putney
Typical project	Guide price
Sink and tap plumbed inIsolation valves, waste and trap	£260–£520
Boiling water tap installedTank under the sink, filter and power supply	£200–£460
Sink moved to a new positionNew supplies and waste run	£520–£1,300
Undermount sink in a stone worktopCut-out and polishing are done by the stone fabricator	Priced with the worktop

Guide ranges cover labour and fittings such as valves, tails and wastes; the sink and tap themselves are extra, and undermount cut-outs in stone are priced with the worktop by the fabricator. Prices include VAT at 20%.

Local homes and their kitchens

Across Greater London you will often find Victorian and Edwardian terraces, conversion flats, mansion block flats and 1930s semis, and each shapes the kitchen differently. Victorian terraces often have a narrow galley beside the side return, while conversion flats and mansion blocks usually fit the kitchen into a small room or along one living-room wall.

Permit parking, red routes and flats without lifts are common, so parking suspensions, stair carries and lift bookings may need arranging before delivery day. London's mains water is hard, so limescale builds quickly on taps and boiling water taps, and a scale-reducing filter is worth planning in.

Building regulations, electrics and gas in Putney

Replacing a sink and tap needs no approval in England, but the plumbing should meet the Water Supply (Water Fittings) Regulations 1999, including isolation valves and backflow protection. Connecting to an existing waste is routine, while a new connection to an underground drain involves building control. A new spur for a boiling water tap on an existing kitchen circuit is not notifiable under Part P, but it must meet BS 7671.

Conservation areas are widespread across London, so a new extractor vent on a front wall may need permission, and leaseholders usually need the freeholder's written consent first.

Getting the most from your sink and tap installation

Ask for the dishwasher and washing machine hoses to be routed so they cannot kink behind the units once the appliances are pushed back into place.
Check the tap's hole size against the sink or worktop before ordering, as some taps need a larger hole than an existing sink provides.
Empty the sink cupboard before fitting day, and plan where cleaning products will go while the waste, trap and valves are being changed.
Ceramic farmhouse-style sinks are heavy and need a base unit designed to carry them, with the worktop planned around the sink.

Questions about sink and tap installation in Putney

How much does sink and tap installation cost in Putney?

Sink and tap installation in Putney typically costs £260 to £520 including VAT for plumbing in a new sink and tap, based on prices in London. Larger or more involved jobs cost more, and your price is fixed in writing after a free survey visit.

Do you work near Putney as well?

Yes. As well as Putney itself, we cover the rest of Greater London and nearby towns such as Roehampton and Barnes. The process is the same wherever the kitchen is.

What is the difference between an inset and an undermount sink?

An inset sink drops into a cut-out from above, with its rim resting on the worktop, and suits laminate, wood and stone. An undermount sink is fixed beneath the worktop so the edge of the cut-out is exposed, which usually calls for a solid, water-resistant material such as stone or solid surface. Undermount cut-outs in stone are cut and polished by the fabricator.

What do I need for a boiling water tap?

A boiling water tap needs a tank in the cupboard under the sink, usually a socket or fused spur to power it, and often a filter, particularly where the water is hard. Some models have a minimum water pressure, so check yours before buying. The tap also needs a correctly sized hole in the sink or worktop and enough clear cupboard space for the tank and pipework.

Do I need isolation valves under my kitchen sink?

They are strongly advised, and we fit them as standard. An isolation valve on each supply to the tap, and on each appliance supply, lets you turn off the water to one fitting without shutting off the whole house. That makes changing a tap cartridge or dealing with a leak far simpler. The valves are left where they can still be reached once the cupboard is in use.

Sink and tap installation near Putney

Close to Putney? We cover these nearby towns too: