Sink and tap installation in Oldham

Why do people in Oldham choose sink and tap installation?

People in Oldham with low water pressure sometimes find a new tap disappointing, so checking the pressure before choosing a tap or boiling water tap saves trouble later.

If you are fitting new stone worktops in your Oldham kitchen, it is a natural point to change to an undermount sink cut and polished by the fabricator. Our Greater Manchester coverage reaches every part of Oldham (OL1) and out towards Chadderton.

What does the job involve?

Every kitchen is different, so we confirm the scope in writing. Most jobs of this kind include:

Inset sink cut-outs made on site in laminate and wood worktops
New sink fitted, sealed and connected to the existing supplies and waste
Waste, overflow and trap fitted, with dishwasher and washing machine waste connections
Ceramic farmhouse-style sinks set on a suitable supporting base unit and sealed
Sink moved to a new position with new supply and waste runs
Every joint leak tested, with water flow and drainage checked before handover

What should you budget for sink and tap installation in Oldham?

The figures below are guide prices for Oldham, including VAT and adjusted for typical costs across the North West. The fixed price comes after we have measured up. Costs across the North West tend to sit under UK averages, which these ranges reflect.

What should you budget for sink and tap installation in Oldham?
Typical project	Guide price
Sink and tap plumbed inIsolation valves, waste and trap	£190–£380
Boiling water tap installedTank under the sink, filter and power supply	£140–£330
Sink moved to a new positionNew supplies and waste run	£380–£950
Undermount sink in a stone worktopCut-out and polishing are done by the stone fabricator	Priced with the worktop

Guide ranges cover labour and fittings such as valves, tails and wastes; the sink and tap themselves are extra, and undermount cut-outs in stone are priced with the worktop by the fabricator. Prices include VAT at 20%.

House types around Oldham and what they mean for a kitchen

You will find Victorian terraces, 1930s semis, converted mill and warehouse flats and post-war estate houses throughout Greater Manchester. Two-up two-down terraces often have a small back kitchen or a galley in the rear outrigger, while 1930s semis usually have a separate kitchen beside the dining room.

Terraced streets with back alleys, city-centre flats with booked lifts and permit parking can all affect delivery timing and how long worktops are carried in. Mains water across Greater Manchester is mostly soft, so limescale is less of a problem and taps and boiling water taps tend to stay cleaner.

What rules apply to sink and tap installation in Oldham?

Replacing a sink and tap needs no approval in England, but the plumbing should meet the Water Supply (Water Fittings) Regulations 1999, including isolation valves and backflow protection. Connecting to an existing waste is routine, while a new connection to an underground drain involves building control. A new spur for a boiling water tap on an existing kitchen circuit is not notifiable under Part P, but it must meet BS 7671.

Listed mill conversions and homes in conservation areas may need consent for new external vents, and apartment owners usually need the freeholder's or managing agent's consent.

Planning ahead

Choose the sink before stone worktops are templated in your Oldham kitchen, so the fabricator can cut and polish the undermount opening to suit it.
Check the tap's hole size against the sink or worktop before ordering, as some taps need a larger hole than an existing sink provides.
Find the stopcock in your Oldham home before the plumber arrives and check it turns off fully, as older stopcocks can stick or let water past.
Moving the sink means new supply and waste runs, so check the waste can fall properly to the drain or stack from the new position.

Questions about sink and tap installation in Oldham

How much does sink and tap installation cost in Oldham?

Guide prices in Oldham are about £190 to £380 including VAT for plumbing in a new sink and tap. The final price depends on the size of the kitchen and what is moving, and is set out in an itemised written quote.

Which parts of Oldham do you work in?

All of them. Our Greater Manchester coverage takes in the whole of Oldham, including the OL1 postcode district, as well as surrounding towns such as Chadderton. If you are unsure, send us your postcode.

Do I need isolation valves under my kitchen sink?

They are strongly advised, and we fit them as standard. An isolation valve on each supply to the tap, and on each appliance supply, lets you turn off the water to one fitting without shutting off the whole house. That makes changing a tap cartridge or dealing with a leak far simpler. The valves are left where they can still be reached once the cupboard is in use.

Can a dishwasher and washing machine drain through the sink waste?

Yes, in most kitchens. The sink trap can take an appliance connection on a spigot, or a separate standpipe can be fitted. The appliance hose needs to rise to the height its manufacturer specifies before it drops to the waste, so dirty water cannot siphon back. Two appliances can usually share a double-spigot trap, which we plan with the sink.

What is the difference between an inset and an undermount sink?

An inset sink drops into a cut-out from above, with its rim resting on the worktop, and suits laminate, wood and stone. An undermount sink is fixed beneath the worktop so the edge of the cut-out is exposed, which usually calls for a solid, water-resistant material such as stone or solid surface. Undermount cut-outs in stone are cut and polished by the fabricator.

Nearby places we cover

We also carry out sink and tap installation in these towns near Oldham: