Sink and tap installation in Folkestone

Why do people in Folkestone choose sink and tap installation?

If a new dishwasher or washing machine is going next to the sink in your Folkestone home, the trap and waste connections usually need changing as well.

Landlords in Kent often swap tired sinks and taps between tenancies, choosing hard-wearing finishes and accessible valves so that later repairs are quick and cheap. If your home is in Folkestone or close by in Hythe, Kent or Dover, the same survey, quote and fitting process applies.

What is included in the work?

Your written quote lists everything included. For sink and tap installation, that normally means:

Inset sink cut-outs made on site in laminate and wood worktops
Waste, overflow and trap fitted, with dishwasher and washing machine waste connections
Isolation valves on the hot and cold supplies, with flexible tap tails connected
New sink fitted, sealed and connected to the existing supplies and waste
Ceramic farmhouse-style sinks set on a suitable supporting base unit and sealed
Every joint leak tested, with water flow and drainage checked before handover

Guide prices for sink and tap installation in Folkestone

The figures below are guide prices for Folkestone, including VAT and adjusted for typical costs across the South East. The fixed price comes after we have measured up. Prices in the South East usually run above the national guide, mainly because labour and parking cost more.

Guide prices for sink and tap installation in Folkestone
Typical project	Guide price
Sink and tap plumbed inIsolation valves, waste and trap	£230–£460
Boiling water tap installedTank under the sink, filter and power supply	£170–£400
Sink moved to a new positionNew supplies and waste run	£460–£1,200
Undermount sink in a stone worktopCut-out and polishing are done by the stone fabricator	Priced with the worktop

Guide ranges cover labour and fittings such as valves, tails and wastes; the sink and tap themselves are extra, and undermount cut-outs in stone are priced with the worktop by the fabricator. Prices include VAT at 20%.

What kind of kitchens do we fit in Folkestone?

Across Kent you will often find Victorian terraces, weatherboarded cottages, 1930s semis and oast house conversions, and each shapes the kitchen differently. Victorian terraces in the Medway towns and along the coast often have a narrow back-addition kitchen, while 1930s semis usually have a small kitchen beside a separate dining room.

Water across Kent is hard, so limescale builds up quickly on taps and boiling water taps, and a scale-reducing filter is worth considering. Seaside terraces, permit parking and narrow village lanes can each make deliveries slower, so the route for long worktops is best checked at the survey.

Regulations for kitchen work in Folkestone

Replacing a sink and tap needs no approval in England, but the plumbing should meet the Water Supply (Water Fittings) Regulations 1999, including isolation valves and backflow protection. Connecting to an existing waste is routine, while a new connection to an underground drain involves building control. A new spur for a boiling water tap on an existing kitchen circuit is not notifiable under Part P, but it must meet BS 7671.

Listed weatherboarded and timber-framed cottages, oast conversions and homes in conservation areas such as historic Canterbury may need consent for new external vents.

Tips before you start

Find the stopcock in your Folkestone home before the plumber arrives and check it turns off fully, as older stopcocks can stick or let water past.
Ask for the dishwasher and washing machine hoses to be routed so they cannot kink behind the units once the appliances are pushed back into place.
Check the tap's hole size against the sink or worktop before ordering, as some taps need a larger hole than an existing sink provides.
If a dishwasher or washing machine sits next to the sink, plan their waste connections and the trap layout together with the sink.

Questions about sink and tap installation in Folkestone

How much does sink and tap installation cost in Folkestone?

For plumbing in a new sink and tap, budget around £230 to £460 including VAT in Folkestone. That reflects typical costs in the South East; we confirm the actual figure in writing once we have measured up.

Which parts of Folkestone do you work in?

All of them. Our Kent coverage takes in the whole of Folkestone, including the CT19 postcode district, as well as surrounding towns such as Hythe, Kent. If you are unsure, send us your postcode.

What is the difference between an inset and an undermount sink?

An inset sink drops into a cut-out from above, with its rim resting on the worktop, and suits laminate, wood and stone. An undermount sink is fixed beneath the worktop so the edge of the cut-out is exposed, which usually calls for a solid, water-resistant material such as stone or solid surface. Undermount cut-outs in stone are cut and polished by the fabricator.

What do I need for a boiling water tap?

A boiling water tap needs a tank in the cupboard under the sink, usually a socket or fused spur to power it, and often a filter, particularly where the water is hard. Some models have a minimum water pressure, so check yours before buying. The tap also needs a correctly sized hole in the sink or worktop and enough clear cupboard space for the tank and pipework.

Can a dishwasher and washing machine drain through the sink waste?

Yes, in most kitchens. The sink trap can take an appliance connection on a spigot, or a separate standpipe can be fitted. The appliance hose needs to rise to the height its manufacturer specifies before it drops to the waste, so dirty water cannot siphon back. Two appliances can usually share a double-spigot trap, which we plan with the sink.

Sink and tap installation near Folkestone

We also carry out sink and tap installation in these towns near Folkestone: