Sink and tap installation in Bath

Why do people in Bath choose sink and tap installation?

Plenty of people in Bath replace a sink and tap on their own when the tap drips, the bowl is stained or the waste drains slowly, without touching the rest of the kitchen.

If a new dishwasher or washing machine is going next to the sink in your Bath home, the trap and waste connections usually need changing as well. If your home is in Bath or close by in Keynsham or Trowbridge, the same survey, quote and fitting process applies.

What does the job involve?

After the survey visit we write the scope down. For sink and tap installation in Bath it usually covers:

New sink fitted, sealed and connected to the existing supplies and waste
Sink moved to a new position with new supply and waste runs
Ceramic farmhouse-style sinks set on a suitable supporting base unit and sealed
Isolation valves on the hot and cold supplies, with flexible tap tails connected
Every joint leak tested, with water flow and drainage checked before handover
Boiling water tap fitted with its tank, filter and power supply in the cupboard

Guide prices for sink and tap installation in Bath

Typical sink and tap installation prices for homes in Bath, including VAT and adjusted for the South West. Your own figure depends on the size of the kitchen, the layout and what is moving. For the South West, these ranges are close to the national figures.

Guide prices for sink and tap installation in Bath
Typical project	Guide price
Sink and tap plumbed inIsolation valves, waste and trap	£210–£410
Boiling water tap installedTank under the sink, filter and power supply	£150–£360
Sink moved to a new positionNew supplies and waste run	£410–£1,000
Undermount sink in a stone worktopCut-out and polishing are done by the stone fabricator	Priced with the worktop

Guide ranges cover labour and fittings such as valves, tails and wastes; the sink and tap themselves are extra, and undermount cut-outs in stone are priced with the worktop by the fabricator. Prices include VAT at 20%.

Kitchens in homes around Bath

The housing mix across Somerset includes Georgian townhouses, Victorian terraces, stone cottages and post-war estate houses, so no two kitchen fits are quite alike. Georgian townhouses in Bath often have kitchens at lower-ground level or in flats on upper floors, while Victorian terraces in Taunton and Yeovil tend to have a narrow back galley.

Steep streets and controlled parking in Bath, upper-floor flats without lifts and narrow village lanes can each make delivering worktops slower. Somerset's mains water is mostly hard, so limescale on taps and boiling water taps is common, and a filter or softener can help keep them working well.

Regulations for kitchen work in Bath

Replacing a sink and tap needs no approval in England, but the plumbing should meet the Water Supply (Water Fittings) Regulations 1999, including isolation valves and backflow protection. Connecting to an existing waste is routine, while a new connection to an underground drain involves building control. A new spur for a boiling water tap on an existing kitchen circuit is not notifiable under Part P, but it must meet BS 7671.

Bath is a World Heritage city with many listed buildings, and homes in Exmoor National Park or conservation areas may need consent for new vents or internal changes.

Practical advice for Bath homeowners

For a ceramic farmhouse-style sink in your Bath kitchen, confirm the base unit is designed for it, as a standard sink unit may not carry the weight.
Check the tap's hole size against the sink or worktop before ordering, as some taps need a larger hole than an existing sink provides.
Find the stopcock in your Bath home before the plumber arrives and check it turns off fully, as older stopcocks can stick or let water past.
Moving the sink means new supply and waste runs, so check the waste can fall properly to the drain or stack from the new position.

Questions about sink and tap installation in Bath

How much does sink and tap installation cost in Bath?

For plumbing in a new sink and tap, budget around £210 to £410 including VAT in Bath. That reflects typical costs in the South West; we confirm the actual figure in writing once we have measured up.

Do you work near Bath as well?

Yes. As well as Bath itself, we cover the rest of Somerset and nearby towns such as Keynsham and Trowbridge. The process is the same wherever the kitchen is.

What do I need for a boiling water tap?

A boiling water tap needs a tank in the cupboard under the sink, usually a socket or fused spur to power it, and often a filter, particularly where the water is hard. Some models have a minimum water pressure, so check yours before buying. The tap also needs a correctly sized hole in the sink or worktop and enough clear cupboard space for the tank and pipework.

Can a dishwasher and washing machine drain through the sink waste?

Yes, in most kitchens. The sink trap can take an appliance connection on a spigot, or a separate standpipe can be fitted. The appliance hose needs to rise to the height its manufacturer specifies before it drops to the waste, so dirty water cannot siphon back. Two appliances can usually share a double-spigot trap, which we plan with the sink.

What is the difference between an inset and an undermount sink?

An inset sink drops into a cut-out from above, with its rim resting on the worktop, and suits laminate, wood and stone. An undermount sink is fixed beneath the worktop so the edge of the cut-out is exposed, which usually calls for a solid, water-resistant material such as stone or solid surface. Undermount cut-outs in stone are cut and polished by the fabricator.

Also covering nearby towns

The same service is available a short drive from Bath, including: