Kitchen plumbing in Washington

What prompts kitchen plumbing in Washington?

When a kitchen in Washington goes from a closed room to an open-plan space, the sink and dishwasher often move to a new wall with new waste runs.

People adding a boiling water tap in Washington usually need a fresh cold feed and room under the sink for the tank, planned alongside the sink unit. Kitchens in every part of Washington are covered, and the survey visit is free wherever you are in Tyne and Wear.

What we cover for kitchen plumbing in Washington

After the survey visit we write the scope down. For kitchen plumbing in Washington it usually covers:

Radiators moved or replaced so they clear the new units
A survey of the stopcock, supply pipes, waste route and drain connection
Isolation valves on each tap and appliance feed for quick shut-off
Waste pipes laid to a steady fall, with an access point for clearing blockages
Dishwasher and washing machine supplies, with waste connections through suitable traps
Hot and cold supplies run to the new sink position

Kitchen plumbing prices in Washington

These guide ranges include VAT at 20% and are adjusted for prices in the North East. We confirm your price in writing after a free survey visit. Prices in the North East usually come in below the national guide, as labour rates are lower than in the South East.

Kitchen plumbing prices in Washington
Typical project	Guide price
Sink, dishwasher and washing machine connectionsSupplies, valves and wastes in the new layout	£180–£450
Sink relocated, or new supplies for a boiling water tapNew pipe and waste runs	£360–£900
Waste run across a solid concrete floorChasing, pipework and reinstating the floor	£540–£1,400
Radiator moved or replacedDrain down, new pipework and refill	£220–£450

Guide ranges cover labour, pipework, fittings, valves and traps; the sink, tap and appliances themselves, any gas work and any building control or building warrant fees are not included. Prices include VAT at 20%.

Local homes and their kitchens

The housing mix across Tyne and Wear includes tyneside flats, Victorian terraces, 1930s semis and post-war council-built houses, so no two kitchen fits are quite alike. Tyneside flats often have a narrow kitchen in the rear offshoot, while 1930s semis and ex-council houses tend to have a small square kitchen at the back.

Hardness varies across Tyne and Wear, from fairly soft around Newcastle to harder in parts of Sunderland, so check with your supplier before choosing a filter. Back lanes behind terraced streets can help deliveries, but upper Tyneside flats have their own internal stair, so long worktops need careful handling.

What rules apply to kitchen plumbing in Washington?

In England, kitchen pipework and fittings must meet the Water Supply (Water Fittings) Regulations 1999, which cover suitable materials, backflow protection and preventing waste or contamination of the supply. Connecting a sink to an existing waste or stack is routine, but a new connection to an underground drain, or a change to how waste water is discharged, involves building control. Gas pipework to a hob or cooker is separate work for a Gas Safe registered engineer.

In conservation areas and listed buildings, such as parts of central Newcastle and Tynemouth, a new external vent or changes to historic features may need consent.

Planning ahead

In a flat in Washington, check your lease before moving the sink, as moving services usually needs the freeholder's written consent.
If your house in Tyne and Wear has a solid floor, ask at the survey where a waste could run before you settle on an island sink.
Ask for supplies and wastes to be positioned to suit each appliance's instructions, so hoses are short and do not kink.
Put the dishwasher next to the sink so its supply and waste stay short, easy to reach and less likely to block.

Questions about kitchen plumbing in Washington

How much does kitchen plumbing cost in Washington?

Guide prices in Washington are about £180 to £450 including VAT for connecting the sink, dishwasher and washing machine. The final price depends on the size of the kitchen and what is moving, and is set out in an itemised written quote.

Do you cover all of Washington?

Yes. We work across Washington, including the NE37 and NE38 postcode districts, and nearby towns such as Chester-le-Street and Felling. Book a free survey visit and we will arrange a time that suits you.

What happens to the old pipes during a kitchen refit?

Pipes that will no longer serve anything are cut back to the nearest live pipe and capped, rather than left as long dead ends behind the new units. Water sitting in an unused length of pipe can go stale, and a forgotten joint can leak where nobody will see it. Old wastes are removed or sealed so they cannot let drain smells back into the room.

Can a kitchen sink be moved to a different wall?

Yes, usually. The supplies are the easy part; the waste decides it, because it needs a steady fall all the way to the stack or drain. On a suspended timber floor the pipe can often run between the joists, while on solid concrete a channel may need to be cut and filled. Where a fall cannot be achieved, a pumped waste is sometimes considered.

Why should every appliance have an isolation valve?

An isolation valve lets you shut off the water to one tap or appliance without turning off the whole house. If a dishwasher hose splits or a tap needs a new cartridge, you turn a small screw or lever under the sink and the rest of the home keeps running. Valves are fitted on the hot and cold tap feeds and on each appliance supply.

Kitchen plumbing near Washington

The same service is available a short drive from Washington, including: