Cooker hood installation in Long Eaton

Thinking about cooker hood installation in Long Eaton?

If condensation runs down the windows of your Long Eaton kitchen whenever you cook, the hood may be recirculating, undersized or ducted through a long, flexible run.

If your Long Eaton kitchen has an older open-flued boiler, fitting a stronger hood needs care, as it can affect the flue and should be followed by a spillage test. Long Eaton sits about 9 miles east of Derby, and our Derbyshire coverage takes in everything in between.

What does the job involve?

Every kitchen is different, so we confirm the scope in writing. Most jobs of this kind include:

Hood fixed at the height set by the hood and hob manufacturers
Power supply connected by an electrician and tested to BS 7671
Spillage test by a Gas Safe registered engineer where an open-flued appliance is present
Core drilling through the outside wall and an external grille fitted and sealed
Survey of the hob position, duct route, outside wall and any open-flued appliance
Short, straight runs of rigid ducting wherever the route allows

Cooker hood installation prices in Long Eaton

Use these ranges to plan your budget. They include VAT, reflect costs in the East Midlands, and are firmed up once we have seen your Long Eaton kitchen. Costs in the East Midlands sit close to the national guide.

Cooker hood installation prices in Long Eaton
Typical project	Guide price
Like-for-like cooker hood swapSame position and ducting	£120–£230
New ducted hood through an outside wallCore drilling, ducting run and external grille	£290–£870
Island or ceiling hood installedTwo-person install, fixings to the ceiling structure	£290–£610
Recirculating hood fittedNo ducting; carbon filters need replacing	£120–£290

Guide ranges cover fitting and connection with standard ducting through a straightforward wall; long or concealed duct runs, ceiling repairs, new electrical spurs, spillage tests and the hood itself are priced separately. Prices include VAT at 20%.

Fitting kitchens in older and newer Long Eaton homes

In and around Long Eaton, homes range across gritstone and limestone cottages, Victorian terraces, 1930s semis and former mining village terraces. Terraces in Derby and Chesterfield often have a long galley behind the back room, while stone cottages in the Peak District may have a small kitchen in a rear extension.

Steep hill villages and narrow lanes can limit delivery vehicles, while terraced streets in the towns may have little parking near the front door. Water hardness varies across Derbyshire, so check with your supplier; where it is harder, limescale on taps and boiling water taps is worth planning for.

What rules apply to cooker hood installation in Long Eaton?

In England, Approved Document F guidance for kitchen extract is about 30 litres per second from a cooker hood extracting outside, or 60 litres per second from a fan elsewhere in the room. A recirculating hood does not remove moisture, so another means of extract is usually needed. A new vent through the outside wall of a flat may need planning permission and the freeholder's consent, and an open-flued gas appliance in the room calls for a spillage test.

Homes in the Peak District National Park, listed buildings and conservation areas may need consent for a new vent on a visible wall or alterations to historic features.

Planning ahead

For an island hood in your Long Eaton kitchen, settle the hood position before the ceiling is boarded, so timber supports can be added in the right place.
Choose a hood at least as wide as your hob, and compare its stated extraction rate with the size of the room before you buy.
Before choosing a hood for your Long Eaton kitchen, find the nearest outside wall to the hob, because the shorter the duct run, the better the extraction.
Keep the duct run short and straight with rigid ducting, because every bend and extra metre of flexible hose reduces how much air the hood moves.

Questions about cooker hood installation in Long Eaton

How much does cooker hood installation cost in Long Eaton?

For a like-for-like cooker hood swap, budget around £120 to £230 including VAT in Long Eaton. That reflects typical costs in the East Midlands; we confirm the actual figure in writing once we have measured up.

Do you cover all of Long Eaton?

Yes. We work across Long Eaton, including the NG10 postcode district, and nearby towns such as Ilkeston and Nottingham. Book a free survey visit and we will arrange a time that suits you.

How high should a cooker hood be above the hob?

At least the minimum distance given by the manufacturers. Both the hood and the hob instructions set a minimum gap between them, and where they differ the greater figure should be used. Gas hobs usually need more clearance than induction. A hood fitted too low is a fire risk, while one fitted much higher than recommended captures less steam.

Why might a cooker hood need a spillage test?

Because a hood pulling air out of a room can draw fumes back down the flue of an open-flued gas appliance, such as some older boilers or gas fires. Where the kitchen, or a room open to it, has one, a Gas Safe registered engineer should carry out a spillage test with the hood running at full speed. Room-sealed boilers are not affected in the same way.

Does a cooker hood need a hole in the wall?

A ducted hood does. The usual route is a core-drilled hole through the nearest outside wall, with rigid ducting from the hood and an external grille sealed into the wall. Where the hob is far from an outside wall, the duct can sometimes run above the wall units or through a ceiling void. A recirculating hood needs no hole, but it removes no moisture.

Nearby places we cover

The same service is available a short drive from Long Eaton, including: