Cooker hood installation in Hanworth

When does cooker hood installation make sense in Hanworth?

People in flats across Greater London sometimes rely on recirculating hoods because an outside vent needs consent from the building's owners, and want to know what else improves ventilation.

Homeowners in Hanworth adding a hob to a new island often need a ceiling hood with solid fixings and a duct route planned before the ceiling is closed up. If your home is in Hanworth or close by in Hampton or Feltham, the same survey, quote and fitting process applies.

What is in a typical job?

Your written quote lists everything included. For cooker hood installation, that normally means:

Core drilling through the outside wall and an external grille fitted and sealed
Survey of the hob position, duct route, outside wall and any open-flued appliance
Power supply connected by an electrician and tested to BS 7671
Spillage test by a Gas Safe registered engineer where an open-flued appliance is present
Recirculating hoods fitted with carbon filters, and their limits explained
Short, straight runs of rigid ducting wherever the route allows

Guide prices for cooker hood installation in Hanworth

Typical cooker hood installation prices for homes in Hanworth, including VAT and adjusted for London. Your own figure depends on the size of the kitchen, the layout and what is moving. Prices in London usually run above the national guide, mainly because labour and parking cost more.

Guide prices for cooker hood installation in Hanworth
Typical project	Guide price
Like-for-like cooker hood swapSame position and ducting	£160–£310
New ducted hood through an outside wallCore drilling, ducting run and external grille	£390–£1,200
Island or ceiling hood installedTwo-person install, fixings to the ceiling structure	£390–£820
Recirculating hood fittedNo ducting; carbon filters need replacing	£160–£390

Guide ranges cover fitting and connection with standard ducting through a straightforward wall; long or concealed duct runs, ceiling repairs, new electrical spurs, spillage tests and the hood itself are priced separately. Prices include VAT at 20%.

Local homes and their kitchens

The housing mix across Greater London includes Victorian and Edwardian terraces, conversion flats, mansion block flats and 1930s semis, so no two kitchen fits are quite alike. Victorian terraces often have a narrow galley beside the side return, while conversion flats and mansion blocks usually fit the kitchen into a small room or along one living-room wall.

London's mains water is hard, so limescale builds quickly on taps and boiling water taps, and a scale-reducing filter is worth planning in. Permit parking, red routes and flats without lifts are common, so parking suspensions, stair carries and lift bookings may need arranging before delivery day.

Do you need approval for cooker hood installation in Hanworth?

In England, Approved Document F guidance for kitchen extract is about 30 litres per second from a cooker hood extracting outside, or 60 litres per second from a fan elsewhere in the room. A recirculating hood does not remove moisture, so another means of extract is usually needed. A new vent through the outside wall of a flat may need planning permission and the freeholder's consent, and an open-flued gas appliance in the room calls for a spillage test.

Conservation areas are widespread across London, so a new extractor vent on a front wall may need permission, and leaseholders usually need the freeholder's written consent first.

Worth knowing before the fit

Before choosing a hood for your Hanworth kitchen, find the nearest outside wall to the hob, because the shorter the duct run, the better the extraction.
Choose a hood at least as wide as your hob, and compare its stated extraction rate with the size of the room before you buy.
Replace the carbon filters in a recirculating hood as often as the manufacturer advises, and clean the grease filters regularly so the hood keeps working well.
Check the minimum height above the hob in both the hood and hob instructions, and use the greater of the two figures.

Questions about cooker hood installation in Hanworth

How much does cooker hood installation cost in Hanworth?

Guide prices in Hanworth are about £160 to £310 including VAT for a like-for-like cooker hood swap. The final price depends on the size of the kitchen and what is moving, and is set out in an itemised written quote.

Do you cover all of Hanworth?

Yes. We work across Hanworth, including the TW13 postcode district, and nearby towns such as Hampton and Feltham. Book a free survey visit and we will arrange a time that suits you.

Can a ducted cooker hood be fitted in a flat?

Often, but check consents first. A new vent through the outside wall of a flat may need planning permission and the freeholder's written consent, and some leases do not allow it at all. Where an outside vent is not possible, a recirculating hood can be fitted, with a separate extract fan or other ventilation dealing with moisture. Listed buildings may also need listed building consent.

Should I choose a ducted or a recirculating cooker hood?

A ducted hood is usually more effective, because it takes steam, smoke and smells outside. A recirculating hood passes air through grease and carbon filters and returns it to the room, so it deals with grease and smells but not moisture, and another means of extract is usually needed. Recirculating suits kitchens with no practical duct route, and its carbon filters need replacing.

Does a cooker hood need a hole in the wall?

A ducted hood does. The usual route is a core-drilled hole through the nearest outside wall, with rigid ducting from the hood and an external grille sealed into the wall. Where the hob is far from an outside wall, the duct can sometimes run above the wall units or through a ceiling void. A recirculating hood needs no hole, but it removes no moisture.

Cooker hood installation in neighbouring towns

We also carry out cooker hood installation in these towns near Hanworth: