Cooker hood installation in Edmonton

Why cooker hood installation for an Edmonton home?

People in flats across Greater London sometimes rely on recirculating hoods because an outside vent needs consent from the building's owners, and want to know what else improves ventilation.

If condensation runs down the windows of your Edmonton kitchen whenever you cook, the hood may be recirculating, undersized or ducted through a long, flexible run. Kitchens in every part of Edmonton are covered, and the survey visit is free wherever you are in Greater London.

What is included in the work?

The exact scope is agreed after the survey, but a typical job in Edmonton covers:

Spillage test by a Gas Safe registered engineer where an open-flued appliance is present
Recirculating hoods fitted with carbon filters, and their limits explained
Island and ceiling hoods fixed into the ceiling structure by two people
Survey of the hob position, duct route, outside wall and any open-flued appliance
Core drilling through the outside wall and an external grille fitted and sealed
Hood fixed at the height set by the hood and hob manufacturers

Cooker hood installation prices in Edmonton

The figures below are guide prices for Edmonton, including VAT and adjusted for typical costs across London. The fixed price comes after we have measured up. Prices in London usually run above the national guide, mainly because labour and parking cost more.

Cooker hood installation prices in Edmonton
Typical project	Guide price
Like-for-like cooker hood swapSame position and ducting	£160–£310
New ducted hood through an outside wallCore drilling, ducting run and external grille	£390–£1,200
Island or ceiling hood installedTwo-person install, fixings to the ceiling structure	£390–£820
Recirculating hood fittedNo ducting; carbon filters need replacing	£160–£390

Guide ranges cover fitting and connection with standard ducting through a straightforward wall; long or concealed duct runs, ceiling repairs, new electrical spurs, spillage tests and the hood itself are priced separately. Prices include VAT at 20%.

Local homes and their kitchens

In and around Edmonton, homes range across Victorian and Edwardian terraces, conversion flats, mansion block flats and 1930s semis. Victorian terraces often have a narrow galley beside the side return, while conversion flats and mansion blocks usually fit the kitchen into a small room or along one living-room wall.

Permit parking, red routes and flats without lifts are common, so parking suspensions, stair carries and lift bookings may need arranging before delivery day. London's mains water is hard, so limescale builds quickly on taps and boiling water taps, and a scale-reducing filter is worth planning in.

Building regulations, electrics and gas in Edmonton

In England, Approved Document F guidance for kitchen extract is about 30 litres per second from a cooker hood extracting outside, or 60 litres per second from a fan elsewhere in the room. A recirculating hood does not remove moisture, so another means of extract is usually needed. A new vent through the outside wall of a flat may need planning permission and the freeholder's consent, and an open-flued gas appliance in the room calls for a spillage test.

Conservation areas are widespread across London, so a new extractor vent on a front wall may need permission, and leaseholders usually need the freeholder's written consent first.

Practical advice for Edmonton homeowners

Ask for rigid ducting rather than flexible hose wherever the route allows, as it moves more air, gathers less grease and is usually quieter.
If your Edmonton home is listed, or in a building with strict rules on outside changes, check what is allowed before any hole is cut for a duct.
Check whether your Edmonton home has an open-flued boiler or gas fire, and mention it at the survey so a spillage test can be planned.
Check the minimum height above the hob in both the hood and hob instructions, and use the greater of the two figures.

Questions about cooker hood installation in Edmonton

How much does cooker hood installation cost in Edmonton?

For a like-for-like cooker hood swap, budget around £160 to £310 including VAT in Edmonton. That reflects typical costs in London; we confirm the actual figure in writing once we have measured up.

Do you cover all of Edmonton?

Yes. We work across Edmonton, including the N18 postcode district, and nearby towns such as Tottenham and Enfield. Book a free survey visit and we will arrange a time that suits you.

Should I choose a ducted or a recirculating cooker hood?

A ducted hood is usually more effective, because it takes steam, smoke and smells outside. A recirculating hood passes air through grease and carbon filters and returns it to the room, so it deals with grease and smells but not moisture, and another means of extract is usually needed. Recirculating suits kitchens with no practical duct route, and its carbon filters need replacing.

Does a cooker hood need a hole in the wall?

A ducted hood does. The usual route is a core-drilled hole through the nearest outside wall, with rigid ducting from the hood and an external grille sealed into the wall. Where the hob is far from an outside wall, the duct can sometimes run above the wall units or through a ceiling void. A recirculating hood needs no hole, but it removes no moisture.

How high should a cooker hood be above the hob?

At least the minimum distance given by the manufacturers. Both the hood and the hob instructions set a minimum gap between them, and where they differ the greater figure should be used. Gas hobs usually need more clearance than induction. A hood fitted too low is a fire risk, while one fitted much higher than recommended captures less steam.

Also covering nearby towns

We also carry out cooker hood installation in these towns near Edmonton: