Cooker hood installation in Barking

Thinking about cooker hood installation in Barking?

Homeowners in Barking adding a hob to a new island often need a ceiling hood with solid fixings and a duct route planned before the ceiling is closed up.

A new kitchen in a Barking home can move the hob away from the old vent, so the hood, the duct run and the wall grille all need rethinking together. Our Greater London coverage reaches every part of Barking (IG11) and out towards Ilford.

What is included in the work?

After the survey visit we write the scope down. For cooker hood installation in Barking it usually covers:

Survey of the hob position, duct route, outside wall and any open-flued appliance
Hood fixed at the height set by the hood and hob manufacturers
Spillage test by a Gas Safe registered engineer where an open-flued appliance is present
Core drilling through the outside wall and an external grille fitted and sealed
Power supply connected by an electrician and tested to BS 7671
Recirculating hoods fitted with carbon filters, and their limits explained

Cooker hood installation prices in Barking

Typical cooker hood installation prices for homes in Barking, including VAT and adjusted for London. Your own figure depends on the size of the kitchen, the layout and what is moving. Prices in London usually run above the national guide, mainly because labour and parking cost more.

Cooker hood installation prices in Barking
Typical project	Guide price
Like-for-like cooker hood swapSame position and ducting	£160–£310
New ducted hood through an outside wallCore drilling, ducting run and external grille	£390–£1,200
Island or ceiling hood installedTwo-person install, fixings to the ceiling structure	£390–£820
Recirculating hood fittedNo ducting; carbon filters need replacing	£160–£390

Guide ranges cover fitting and connection with standard ducting through a straightforward wall; long or concealed duct runs, ceiling repairs, new electrical spurs, spillage tests and the hood itself are priced separately. Prices include VAT at 20%.

Local homes and their kitchens

Typical homes in this part of Greater London include Victorian and Edwardian terraces, conversion flats, mansion block flats and 1930s semis. Victorian terraces often have a narrow galley beside the side return, while conversion flats and mansion blocks usually fit the kitchen into a small room or along one living-room wall.

Permit parking, red routes and flats without lifts are common, so parking suspensions, stair carries and lift bookings may need arranging before delivery day. London's mains water is hard, so limescale builds quickly on taps and boiling water taps, and a scale-reducing filter is worth planning in.

Do you need approval for cooker hood installation in Barking?

In England, Approved Document F guidance for kitchen extract is about 30 litres per second from a cooker hood extracting outside, or 60 litres per second from a fan elsewhere in the room. A recirculating hood does not remove moisture, so another means of extract is usually needed. A new vent through the outside wall of a flat may need planning permission and the freeholder's consent, and an open-flued gas appliance in the room calls for a spillage test.

Conservation areas are widespread across London, so a new extractor vent on a front wall may need permission, and leaseholders usually need the freeholder's written consent first.

Tips before you start

Choose a hood at least as wide as your hob, and compare its stated extraction rate with the size of the room before you buy.
If your Barking home is listed, or in a building with strict rules on outside changes, check what is allowed before any hole is cut for a duct.
Ask for rigid ducting rather than flexible hose wherever the route allows, as it moves more air, gathers less grease and is usually quieter.
Check the minimum height above the hob in both the hood and hob instructions, and use the greater of the two figures.

Questions about cooker hood installation in Barking

How much does cooker hood installation cost in Barking?

Cooker hood installation in Barking typically costs £160 to £310 including VAT for a like-for-like cooker hood swap, based on prices in London. Larger or more involved jobs cost more, and your price is fixed in writing after a free survey visit.

Do you work near Barking as well?

Yes. As well as Barking itself, we cover the rest of Greater London and nearby towns such as Ilford and Manor Park. The process is the same wherever the kitchen is.

Should I choose a ducted or a recirculating cooker hood?

A ducted hood is usually more effective, because it takes steam, smoke and smells outside. A recirculating hood passes air through grease and carbon filters and returns it to the room, so it deals with grease and smells but not moisture, and another means of extract is usually needed. Recirculating suits kitchens with no practical duct route, and its carbon filters need replacing.

Can a ducted cooker hood be fitted in a flat?

Often, but check consents first. A new vent through the outside wall of a flat may need planning permission and the freeholder's written consent, and some leases do not allow it at all. Where an outside vent is not possible, a recirculating hood can be fitted, with a separate extract fan or other ventilation dealing with moisture. Listed buildings may also need listed building consent.

Why might a cooker hood need a spillage test?

Because a hood pulling air out of a room can draw fumes back down the flue of an open-flued gas appliance, such as some older boilers or gas fires. Where the kitchen, or a room open to it, has one, a Gas Safe registered engineer should carry out a spillage test with the hood running at full speed. Room-sealed boilers are not affected in the same way.

Also covering nearby towns

We also carry out cooker hood installation in these towns near Barking: