Utility room fitting in Richmond, Greater London

Thinking about utility room fitting in Richmond, Greater London?

In a Richmond, Greater London house where the garage is already used for storage rather than the car, some people fit a run of units and the laundry along one wall.

Larger households in Richmond, Greater London sharing a lot of laundry often want a stacked washer and dryer, a hanging rail and a clear worktop for folding. Richmond, Greater London sits about 8 miles west of Westminster, and our Greater London coverage takes in everything in between.

What we cover for utility room fitting in Richmond, Greater London

The exact scope is agreed after the survey, but a typical job in Richmond, Greater London covers:

Extract fan fitted to clear moisture from washing and drying
Washing machine supply, waste and isolation valve, tested for leaks
Worktop over the washing machine and dryer, supported clear of the appliances
Base, wall and tall units fitted, levelled and fixed to the wall
Stacking kit fitted where the washer and dryer sit one above the other
A vent to outside for a vented dryer, or a drain hose for condenser models

Guide prices for utility room fitting in Richmond, Greater London

The figures below are guide prices for Richmond, Greater London, including VAT and adjusted for typical costs across London. The fixed price comes after we have measured up. Prices in London usually run above the national guide, mainly because labour and parking cost more.

Guide prices for utility room fitting in Richmond, Greater London
Typical project	Guide price
Utility units and worktop fitted (fit only)Three to six units, laminate worktop, panels	£1,600–£3,900
Utility room supplied and fittedUnits, worktop, sink, washer and dryer connections	£3,900–£9,100
New utility plumbing for a sink and washing machineSupplies, waste and valves where none exist	£520–£1,300

Fit-only and supply-and-fit ranges cover units, worktop and standard sink and appliance connections, with new plumbing where none exists as a separate line; extract fans, dryer vents and new circuits are quoted on top. Prices include VAT at 20%.

Local homes and their kitchens

You will find Victorian and Edwardian terraces, conversion flats, mansion block flats and 1930s semis throughout Greater London. Victorian terraces often have a narrow galley beside the side return, while conversion flats and mansion blocks usually fit the kitchen into a small room or along one living-room wall.

Permit parking, red routes and flats without lifts are common, so parking suspensions, stair carries and lift bookings may need arranging before delivery day. London's mains water is hard, so limescale builds quickly on taps and boiling water taps, and a scale-reducing filter is worth planning in.

What rules apply to utility room fitting in Richmond, Greater London?

Fitting a utility room needs no planning permission in England, though a new dryer vent through the outside wall of a flat may need planning permission and the freeholder's consent. Adding sockets to an existing circuit is not notifiable, but a new circuit is, under Part P. Approved Document F sets an extract rate of about 30 litres per second for a utility room, so a new fan should be sized to meet it, and if an open-flued boiler shares the room, a Gas Safe registered engineer should carry out a spillage test once a fan is fitted.

Conservation areas are widespread across London, so a new extractor vent on a front wall may need permission, and leaseholders usually need the freeholder's written consent first.

Before you book utility room fitting in Richmond, Greater London

Before choosing a dryer for your Richmond, Greater London utility, check whether there is an outside wall close enough for a short, straight vent duct.
Ask for an isolation valve on the washing machine supply that can be reached without pulling the machine out from under the worktop.
If the utility will be in the garage of your Richmond, Greater London home, make sure the space stays above freezing in winter for the pipes and machines.
A worktop over appliances needs support at each side and a gap above the machines, so they can be slid out for servicing.

Questions about utility room fitting in Richmond, Greater London

How much does utility room fitting cost in Richmond, Greater London?

Utility room fitting in Richmond, Greater London typically costs £1,600 to £3,900 including VAT for fitting three to six utility units and a worktop you have bought, based on prices in London. Larger or more involved jobs cost more, and your price is fixed in writing after a free survey visit.

Can you measure up in Richmond, Greater London before quoting?

Yes. Every quote starts with a free, no-obligation survey visit to your home in Richmond, Greater London. We measure the room, check the walls, floor and service positions, then send an itemised written quote.

Does a utility room need an extractor fan?

Yes, in most cases. Washing and drying put a lot of moisture into a small space, so extract ventilation is strongly advised: Approved Document F sets a rate of about 30 litres per second for utility rooms in England and Wales, and the building standards in Scotland and Technical Booklet K in Northern Ireland cover ventilation too. An extract fan ducted outside is the usual answer, with a window helping but not replacing it. A vented dryer needs its own duct as well.

Can a worktop go over a washing machine and dryer?

Yes, and it is one of the most common utility layouts. The worktop is supported by units, end panels or a rail at each side rather than resting on the machines, with a small gap above them for vibration and so they can be slid out for servicing. Standard front-loading machines usually fit under a standard-height worktop, but we check the appliance heights against the plan first.

Can a utility room go in a garage or under the stairs?

Often, yes, as long as the space already exists and is usable. In a garage it needs to be dry and protected from frost, with power and a route for water and waste. Under the stairs, check the headroom, the ventilation and whether a door can open fully. We fit units and connect appliances in existing spaces; converting a garage into a habitable room is a separate building project.

Utility room fitting in neighbouring towns

The same service is available a short drive from Richmond, Greater London, including: