Utility room fitting in New Malden

What prompts utility room fitting in New Malden?

Families in New Malden often want the washing machine out of the kitchen, so the noise, the wet laundry and the drying racks have a room of their own.

If your New Malden home has a back lobby or a rear porch with a little spare width, a few units and a stacked washer and dryer can make it a working utility. New Malden sits about 9 miles south-west of Westminster, and our Greater London coverage takes in everything in between.

What is included in the work?

The exact scope is agreed after the survey, but a typical job in New Malden covers:

Base, wall and tall units fitted, levelled and fixed to the wall
Free survey visit to check water, waste, power and outside wall positions
Worktop over the washing machine and dryer, supported clear of the appliances
Washing machine supply, waste and isolation valve, tested for leaks
A vent to outside for a vented dryer, or a drain hose for condenser models
Extract fan fitted to clear moisture from washing and drying

Guide prices for utility room fitting in New Malden

Use these ranges to plan your budget. They include VAT, reflect costs in London, and are firmed up once we have seen your New Malden kitchen. Expect costs in London to sit somewhat above UK averages, reflecting local labour rates.

Guide prices for utility room fitting in New Malden
Typical project	Guide price
Utility units and worktop fitted (fit only)Three to six units, laminate worktop, panels	£1,600–£3,900
Utility room supplied and fittedUnits, worktop, sink, washer and dryer connections	£3,900–£9,100
New utility plumbing for a sink and washing machineSupplies, waste and valves where none exist	£520–£1,300

Fit-only and supply-and-fit ranges cover units, worktop and standard sink and appliance connections, with new plumbing where none exists as a separate line; extract fans, dryer vents and new circuits are quoted on top. Prices include VAT at 20%.

Fitting kitchens in older and newer New Malden homes

In and around New Malden, homes range across Victorian and Edwardian terraces, conversion flats, mansion block flats and 1930s semis. Victorian terraces often have a narrow galley beside the side return, while conversion flats and mansion blocks usually fit the kitchen into a small room or along one living-room wall.

Permit parking, red routes and flats without lifts are common, so parking suspensions, stair carries and lift bookings may need arranging before delivery day. London's mains water is hard, so limescale builds quickly on taps and boiling water taps, and a scale-reducing filter is worth planning in.

Regulations for kitchen work in New Malden

Fitting a utility room needs no planning permission in England, though a new dryer vent through the outside wall of a flat may need planning permission and the freeholder's consent. Adding sockets to an existing circuit is not notifiable, but a new circuit is, under Part P. Approved Document F sets an extract rate of about 30 litres per second for a utility room, so a new fan should be sized to meet it, and if an open-flued boiler shares the room, a Gas Safe registered engineer should carry out a spillage test once a fan is fitted.

Conservation areas are widespread across London, so a new extractor vent on a front wall may need permission, and leaseholders usually need the freeholder's written consent first.

Planning ahead

If your Greater London home has an open-flued boiler in the utility, ask for a spillage test by a Gas Safe registered engineer once an extract fan goes in.
If the utility will be in the garage of your New Malden home, make sure the space stays above freezing in winter for the pipes and machines.
Before choosing a dryer for your New Malden utility, check whether there is an outside wall close enough for a short, straight vent duct.
Under-stairs spaces can take a washer and dryer, but check the headroom, the ventilation and room to pull machines out before committing.

Questions about utility room fitting in New Malden

How much does utility room fitting cost in New Malden?

Guide prices in New Malden are about £1,600 to £3,900 including VAT for fitting three to six utility units and a worktop you have bought. The final price depends on the size of the kitchen and what is moving, and is set out in an itemised written quote.

Can you measure up in New Malden before quoting?

Yes. Every quote starts with a free, no-obligation survey visit to your home in New Malden. We measure the room, check the walls, floor and service positions, then send an itemised written quote.

Can a utility room go in a garage or under the stairs?

Often, yes, as long as the space already exists and is usable. In a garage it needs to be dry and protected from frost, with power and a route for water and waste. Under the stairs, check the headroom, the ventilation and whether a door can open fully. We fit units and connect appliances in existing spaces; converting a garage into a habitable room is a separate building project.

Does a condenser or heat pump dryer need an outside vent?

No. Condenser and heat pump dryers do not need an outside vent, so they can go where a vented dryer cannot. They collect water in a container that has to be emptied, or they can be connected to the waste so they drain automatically, which is easy when the dryer sits beside the washing machine. They still give off some warmth, so the space needs air around it. A vented dryer needs a duct to an outside wall.

Does a utility room need an extractor fan?

Yes, in most cases. Washing and drying put a lot of moisture into a small space, so extract ventilation is strongly advised: Approved Document F sets a rate of about 30 litres per second for utility rooms in England and Wales, and the building standards in Scotland and Technical Booklet K in Northern Ireland cover ventilation too. An extract fan ducted outside is the usual answer, with a window helping but not replacing it. A vented dryer needs its own duct as well.

Also covering nearby towns

We also carry out utility room fitting in these towns near New Malden: