Utility room fitting in Liverpool

Who usually needs utility room fitting in Liverpool?

Larger households in Liverpool sharing a lot of laundry often want a stacked washer and dryer, a hanging rail and a clear worktop for folding.

In a Liverpool house where the garage is already used for storage rather than the car, some people fit a run of units and the laundry along one wall. Kitchens in every part of Liverpool are covered, and the survey visit is free wherever you are in Merseyside.

What is in a typical job?

Every kitchen is different, so we confirm the scope in writing. Most jobs of this kind include:

Washing machine supply, waste and isolation valve, tested for leaks
Worktop over the washing machine and dryer, supported clear of the appliances
Extract fan fitted to clear moisture from washing and drying
Free survey visit to check water, waste, power and outside wall positions
Stacking kit fitted where the washer and dryer sit one above the other
A vent to outside for a vented dryer, or a drain hose for condenser models

What does utility room fitting cost in Liverpool?

These guide ranges include VAT at 20% and are adjusted for prices in the North West. We confirm your price in writing after a free survey visit. Prices in the North West usually come in below the national guide, as labour rates are lower than in the South East.

What does utility room fitting cost in Liverpool?
Typical project	Guide price
Utility units and worktop fitted (fit only)Three to six units, laminate worktop, panels	£1,100–£2,800
Utility room supplied and fittedUnits, worktop, sink, washer and dryer connections	£2,800–£6,600
New utility plumbing for a sink and washing machineSupplies, waste and valves where none exist	£380–£950

Fit-only and supply-and-fit ranges cover units, worktop and standard sink and appliance connections, with new plumbing where none exists as a separate line; extract fans, dryer vents and new circuits are quoted on top. Prices include VAT at 20%.

Fitting kitchens in older and newer Liverpool homes

You will find Victorian terraces, Victorian and Edwardian villas, 1930s semis and converted warehouse flats throughout Merseyside. Two-up two-down terraces often have a small back kitchen off the living room, while 1930s semis tend to have a separate kitchen with space to open into a dining room.

Terraced streets with back entries, city-centre flats with booked lifts and permit parking zones can all affect how and when a kitchen is delivered. Merseyside's mains water is soft, so limescale is rarely a big issue and taps, sinks and boiling water taps stay cleaner for longer.

Do you need approval for utility room fitting in Liverpool?

Fitting a utility room needs no planning permission in England, though a new dryer vent through the outside wall of a flat may need planning permission and the freeholder's consent. Adding sockets to an existing circuit is not notifiable, but a new circuit is, under Part P. Approved Document F sets an extract rate of about 30 litres per second for a utility room, so a new fan should be sized to meet it, and if an open-flued boiler shares the room, a Gas Safe registered engineer should carry out a spillage test once a fan is fitted.

Conservation areas and listed buildings are common in older parts of Liverpool and the Wirral, so a new vent on a visible wall may need consent.

Planning ahead

Plan the sockets in your Liverpool utility so each appliance can be switched off at an accessible switch without moving the machine.
Measure the washer and dryer heights, including any stacking kit, before ordering wall units or shelves to go above them.
Ask for an isolation valve on the washing machine supply that can be reached without pulling the machine out from under the worktop.
A worktop over appliances needs support at each side and a gap above the machines, so they can be slid out for servicing.

Questions about utility room fitting in Liverpool

How much does utility room fitting cost in Liverpool?

Utility room fitting in Liverpool typically costs £1,100 to £2,800 including VAT for fitting three to six utility units and a worktop you have bought, based on prices in the North West. Larger or more involved jobs cost more, and your price is fixed in writing after a free survey visit.

Do you cover all of Liverpool?

Yes. We work across Liverpool, including the L1, L2, L3, L4, L5 and L6 postcode districts, and nearby towns such as Kirkdale and Birkenhead. Book a free survey visit and we will arrange a time that suits you.

Can a worktop go over a washing machine and dryer?

Yes, and it is one of the most common utility layouts. The worktop is supported by units, end panels or a rail at each side rather than resting on the machines, with a small gap above them for vibration and so they can be slid out for servicing. Standard front-loading machines usually fit under a standard-height worktop, but we check the appliance heights against the plan first.

Does a utility room need an extractor fan?

Yes, in most cases. Washing and drying put a lot of moisture into a small space, so extract ventilation is strongly advised: Approved Document F sets a rate of about 30 litres per second for utility rooms in England and Wales, and the building standards in Scotland and Technical Booklet K in Northern Ireland cover ventilation too. An extract fan ducted outside is the usual answer, with a window helping but not replacing it. A vented dryer needs its own duct as well.

Does a condenser or heat pump dryer need an outside vent?

No. Condenser and heat pump dryers do not need an outside vent, so they can go where a vented dryer cannot. They collect water in a container that has to be emptied, or they can be connected to the waste so they drain automatically, which is easy when the dryer sits beside the washing machine. They still give off some warmth, so the space needs air around it. A vented dryer needs a duct to an outside wall.

Nearby places we cover

Neighbouring towns where we offer utility room fitting: