Utility room fitting in Gelligaer

Is utility room fitting right for your Gelligaer kitchen?

Families in Gelligaer often want the washing machine out of the kitchen, so the noise, the wet laundry and the drying racks have a room of their own.

When a new kitchen is being planned in Gwent, moving the laundry to a utility often makes room for deep drawers or a dishwasher in the kitchen itself. If your home is in Gelligaer or close by in Blackwood or Pontypridd, the same survey, quote and fitting process applies.

What is in a typical job?

Your written quote lists everything included. For utility room fitting, that normally means:

Stacking kit fitted where the washer and dryer sit one above the other
Base, wall and tall units fitted, levelled and fixed to the wall
Free survey visit to check water, waste, power and outside wall positions
Utility sink and tap plumbed in, with new supplies and waste where none exist
Worktop over the washing machine and dryer, supported clear of the appliances
A vent to outside for a vented dryer, or a drain hose for condenser models

Guide prices for utility room fitting in Gelligaer

The figures below are guide prices for Gelligaer, including VAT and adjusted for typical costs across Wales. The fixed price comes after we have measured up. Prices in Wales usually come in below the national guide, as labour rates are lower than in the South East.

Guide prices for utility room fitting in Gelligaer
Typical project	Guide price
Utility units and worktop fitted (fit only)Three to six units, laminate worktop, panels	£1,100–£2,800
Utility room supplied and fittedUnits, worktop, sink, washer and dryer connections	£2,800–£6,400
New utility plumbing for a sink and washing machineSupplies, waste and valves where none exist	£370–£920

Fit-only and supply-and-fit ranges cover units, worktop and standard sink and appliance connections, with new plumbing where none exists as a separate line; extract fans, dryer vents and new circuits are quoted on top. Prices include VAT at 20%.

Fitting kitchens in older and newer Gelligaer homes

Across Gwent you will often find valley terraces, Victorian villas, post-war council-built houses and new-build estates, and each shapes the kitchen differently. Valley terraces often have a small kitchen in the rear extension, while Victorian villas in Newport and post-war houses in Cwmbran tend to have a separate kitchen and dining room.

Steep valley streets, terraces with steps up to the door and limited parking can make carrying long worktops difficult, so access is checked at the survey. Water across most of Gwent is soft to moderately soft, which is kinder to taps, though some areas are harder, so check with your supplier.

Building regulations, electrics and gas in Gelligaer

In Wales, a utility room needs no planning permission; a listed building may need listed building consent, and a new vent through the outside wall of a flat may need planning permission. New circuits are notifiable under Part P, and so is extending a circuit within a kitchen, which covers a utility area that is part of the kitchen itself. The Welsh Approved Document F sets an extract rate for utility rooms, so a new fan should be sized to meet it, and a Gas Safe registered engineer should spillage-test any open-flued boiler in the room after a fan goes in.

The northern edge of Gwent falls within Bannau Brycheiniog National Park, and listed buildings or conservation areas elsewhere may need consent for new external vents.

Tips before you start

Leave room behind the washing machine for the hoses; pushing it hard against the wall can kink them and stop the water draining properly.
Ask for an isolation valve on the washing machine supply that can be reached without pulling the machine out from under the worktop.
Measure the washer and dryer heights, including any stacking kit, before ordering wall units or shelves to go above them.
Check which dryer you have: a vented dryer needs a duct to an outside wall, while condenser and heat pump dryers need emptying or a drain.

Questions about utility room fitting in Gelligaer

How much does utility room fitting cost in Gelligaer?

For fitting three to six utility units and a worktop you have bought, budget around £1,100 to £2,800 including VAT in Gelligaer. That reflects typical costs in Wales; we confirm the actual figure in writing once we have measured up.

Do you cover all of Gelligaer?

Yes. We work across Gelligaer, including the CF82 postcode district, and nearby towns such as Blackwood and Pontypridd. Book a free survey visit and we will arrange a time that suits you.

Can a utility room go in a garage or under the stairs?

Often, yes, as long as the space already exists and is usable. In a garage it needs to be dry and protected from frost, with power and a route for water and waste. Under the stairs, check the headroom, the ventilation and whether a door can open fully. We fit units and connect appliances in existing spaces; converting a garage into a habitable room is a separate building project.

Does a condenser or heat pump dryer need an outside vent?

No. Condenser and heat pump dryers do not need an outside vent, so they can go where a vented dryer cannot. They collect water in a container that has to be emptied, or they can be connected to the waste so they drain automatically, which is easy when the dryer sits beside the washing machine. They still give off some warmth, so the space needs air around it. A vented dryer needs a duct to an outside wall.

Does a utility room need an extractor fan?

Yes, in most cases. Washing and drying put a lot of moisture into a small space, so extract ventilation is strongly advised: Approved Document F sets a rate of about 30 litres per second for utility rooms in England and Wales, and the building standards in Scotland and Technical Booklet K in Northern Ireland cover ventilation too. An extract fan ducted outside is the usual answer, with a window helping but not replacing it. A vented dryer needs its own duct as well.

Nearby places we cover

We also carry out utility room fitting in these towns near Gelligaer: