Utility room fitting · England
Utility room fitting in East Sussex
If you need utility room fitting anywhere in East Sussex, we survey the kitchen, agree the scope with you and book every trade through to handover.
Is utility room fitting right for your East Sussex kitchen?
Families in East Sussex often want the washing machine out of the kitchen, so the noise, the wet laundry and the drying racks have a room of their own.
Dog owners and keen walkers around East Sussex often ask for a utility with a deep sink, a coat cupboard and somewhere to leave muddy boots and wet jackets.
What does utility room fitting in East Sussex include?
Here is what usually goes into utility room fitting, adjusted to your East Sussex kitchen after we have measured it:
- Free survey visit to check water, waste, power and outside wall positions
- Base, wall and tall units fitted, levelled and fixed to the wall
- Worktop over the washing machine and dryer, supported clear of the appliances
- Washing machine supply, waste and isolation valve, tested for leaks
- A vent to outside for a vented dryer, or a drain hose for condenser models
- Stacking kit fitted where the washer and dryer sit one above the other
- Utility sink and tap plumbed in, with new supplies and waste where none exist
- Extract fan fitted to clear moisture from washing and drying
How much does utility room fitting cost in East Sussex?
These guide ranges include VAT at 20% and are adjusted for prices in the South East. We confirm your price in writing after a free survey visit. Prices in the South East usually run above the national guide, mainly because labour and parking cost more.
| Typical project | Guide price |
|---|---|
| Utility units and worktop fitted (fit only)Three to six units, laminate worktop, panels | £1,400–£3,400 |
| Utility room supplied and fittedUnits, worktop, sink, washer and dryer connections | £3,400–£8,000 |
| New utility plumbing for a sink and washing machineSupplies, waste and valves where none exist | £460–£1,200 |
Fit-only and supply-and-fit ranges cover units, worktop and standard sink and appliance connections, with new plumbing where none exists as a separate line; extract fans, dryer vents and new circuits are quoted on top. Prices include VAT at 20%.
Kitchens in homes across East Sussex
Across East Sussex you will often find Regency townhouses and flats, Victorian terraces, 1930s semis and seaside bungalows, and each shapes the kitchen differently. Regency and Victorian houses split into flats often have small kitchens in former reception rooms, while 1930s semis usually have a compact kitchen at the back.
East Sussex has hard water, so limescale builds up on taps, kettles and boiling water taps, and a filter or softener is worth considering. Seafront flats without lifts, permit parking and steep streets in the coastal towns can make delivery and waste removal slower, so access needs planning.
Flats in converted Regency and Victorian houses often have narrow kitchens that need careful planning to fit a fridge, washing machine and enough worktop. In a 1930s semi or bungalow, opening the kitchen into the dining room is a common change.
Rules for utility room fitting in East Sussex
Fitting a utility room needs no planning permission in England, though a new dryer vent through the outside wall of a flat may need planning permission and the freeholder's consent. Adding sockets to an existing circuit is not notifiable, but a new circuit is, under Part P. Approved Document F sets an extract rate of about 30 litres per second for a utility room, so a new fan should be sized to meet it, and if an open-flued boiler shares the room, a Gas Safe registered engineer should carry out a spillage test once a fan is fitted.
Listed Regency buildings, conservation areas and homes inside the South Downs National Park may need consent for a new external vent, and flat owners usually need freeholder consent.
Before you start
- Check which dryer you have: a vented dryer needs a duct to an outside wall, while condenser and heat pump dryers need emptying or a drain.
- Under-stairs spaces can take a washer and dryer, but check the headroom, the ventilation and room to pull machines out before committing.
- A worktop over appliances needs support at each side and a gap above the machines, so they can be slid out for servicing.
- Stacking the dryer on the washing machine saves width, but it needs a stacking kit that suits both machines and enough height for the pair.
- In an East Sussex flat, check with the freeholder before a new dryer vent or extract fan is cut through an outside wall.
- Leave room behind the washing machine for the hoses; pushing it hard against the wall can kink them and stop the water draining properly.
Questions about utility room fitting in East Sussex
How much does utility room fitting cost in East Sussex?
For fitting three to six utility units and a worktop you have bought, budget around £1,400 to £3,400 including VAT in East Sussex. That reflects typical costs in the South East; we confirm the actual figure in writing once we have measured up.
Do you cover the whole of East Sussex?
Yes. We carry out utility room fitting across East Sussex, including Brighton, Eastbourne, Hastings and Hove. Every job starts with a free survey visit and an itemised written quote.
Can a utility room go in a garage or under the stairs?
Often, yes, as long as the space already exists and is usable. In a garage it needs to be dry and protected from frost, with power and a route for water and waste. Under the stairs, check the headroom, the ventilation and whether a door can open fully. We fit units and connect appliances in existing spaces; converting a garage into a habitable room is a separate building project.
Can a worktop go over a washing machine and dryer?
Yes, and it is one of the most common utility layouts. The worktop is supported by units, end panels or a rail at each side rather than resting on the machines, with a small gap above them for vibration and so they can be slid out for servicing. Standard front-loading machines usually fit under a standard-height worktop, but we check the appliance heights against the plan first.
Does a condenser or heat pump dryer need an outside vent?
No. Condenser and heat pump dryers do not need an outside vent, so they can go where a vented dryer cannot. They collect water in a container that has to be emptied, or they can be connected to the waste so they drain automatically, which is easy when the dryer sits beside the washing machine. They still give off some warmth, so the space needs air around it. A vented dryer needs a duct to an outside wall.
Utility room fitting in towns across East Sussex
Choose a town for local guide prices and postcode coverage:
- Utility room fitting in Brighton
- Utility room fitting in Eastbourne
- Utility room fitting in Hastings
- Utility room fitting in Hove
- Utility room fitting in Bexhill-on-Sea
- Utility room fitting in Hailsham
- Utility room fitting in Seaford
- Utility room fitting in Rottingdean
- Utility room fitting in Crowborough
- Utility room fitting in Portslade
- Utility room fitting in Peacehaven
- Utility room fitting in Uckfield
- Utility room fitting in Lewes
- Utility room fitting in Rye
- Utility room fitting in Battle