Kitchen worktop fitting in Cannock

Is kitchen worktop fitting right for your Cannock kitchen?

If your Staffordshire kitchen still has a dated tiled or laminate surface, new worktops often go in with a new sink, tap and splashback at the same time.

When a Cannock kitchen is about to be sold or let, new worktops and upstands can make the room look cared for without replacing any of the units. We work throughout Cannock (WS11) and across the wider Staffordshire area.

What does the job involve?

Every kitchen is different, so we confirm the scope in writing. Most jobs of this kind include:

Undermount sink and hob cut-outs cut and finished by the stone fabricator
Laminate jointed with a mason's mitre or joint strips, and every cut edge sealed
Quartz, granite or sintered stone templated once the base units are fixed and level
Sink, tap and hob reconnected, with gas hobs connected by Gas Safe registered engineers
Matching upstands fitted and the joint to the wall sealed
Free survey visit to measure the runs and check the base units are level

Guide prices for kitchen worktop fitting in Cannock

These guide ranges include VAT at 20% and are adjusted for prices in the West Midlands. We confirm your price in writing after a free survey visit. For the West Midlands, these ranges are close to the national figures.

Guide prices for kitchen worktop fitting in Cannock
Typical project	Guide price
Laminate worktops, supplied and fittedTypical kitchen, joints, cut-outs and upstands	£500–£1,200
Solid wood worktops, supplied and fittedOiled before and after fitting	£900–£1,800
Granite, templated and fittedTemplate visit, cutting, delivery and fitting	£1,500–£3,200
Quartz, templated and fittedTemplate visit, cutting, delivery and fitting	£1,800–£3,500
Old worktops removed and taken awayMore for stone	£80–£250

Guide ranges are for a typical kitchen and include the worktops, cut-outs, upstands and fitting; removing old tops is a separate line, and new sinks, taps and splashbacks are priced on top. Prices include VAT at 20%.

What kind of kitchens do we fit in Cannock?

The housing mix across Staffordshire includes Victorian terraces, 1930s semis, post-war estate houses and moorland stone cottages, so no two kitchen fits are quite alike. Terraces in Stoke-on-Trent often have a small kitchen in the rear offshoot, while 1930s semis and estate houses tend to have a compact kitchen beside the dining room.

Terraced streets with limited parking and narrow moorland lanes in the north of the county can complicate deliveries, so vehicle size and timing are planned ahead. Water across much of Staffordshire is moderately hard to hard, so limescale on taps and boiling water taps is worth planning for.

Regulations for kitchen work in Cannock

New worktops need no planning permission or Building Regulations approval in England. Disconnecting and reconnecting a gas hob must be done by a Gas Safe registered engineer, and an electric hob or oven goes back on its existing circuit. Moving or adding sockets above the worktop on an existing kitchen circuit is not notifiable, but it must meet BS 7671. In a listed building, check before removing any original fitted joinery.

Homes within the Staffordshire part of the Peak District National Park, listed buildings and conservation areas may need consent for new vents or alterations to historic features.

Planning ahead

Plan the joint positions before ordering laminate, keeping them away from the sink and dishwasher, where water is most likely to sit.
For a Cannock kitchen with stone worktops, ask whether the upstands will be cut from the same slab so the colour and pattern match.
Before templating day at your Cannock home, make sure the sink, tap and hob are on site so the stone can be cut to them.
Quartz and granite are heavy; the units must be sound, level and well fixed, and any swollen or weak carcasses replaced first.

Questions about kitchen worktop fitting in Cannock

How much does kitchen worktop fitting cost in Cannock?

Kitchen worktop fitting in Cannock typically costs £500 to £1,200 including VAT for laminate worktops, supplied and fitted, based on prices in the West Midlands. Larger or more involved jobs cost more, and your price is fixed in writing after a free survey visit.

Can you measure up in Cannock before quoting?

Yes. Every quote starts with a free, no-obligation survey visit to your home in Cannock. We measure the room, check the walls, floor and service positions, then send an itemised written quote.

How are laminate worktops joined at corners?

With either a mason's mitre or a joint strip. A mason's mitre is routed with a jig so the front edge profile turns the corner, then glued, sealed and pulled tight with connector bolts underneath. A joint strip is a metal or colour-matched profile fixed and sealed between the two lengths. Either way, every cut edge, including the sink and hob cut-outs, is sealed so water cannot swell the core.

How do I look after a solid wood worktop?

Oil it regularly and keep it away from standing water. Wood is oiled on every face before fitting and given further coats once in place, then re-oiled more often in the first months. Wipe up round the sink and tap, and do not leave wet cloths or a dripping kettle on it. It is fixed with slotted brackets so it can expand and shrink with the seasons without cracking.

Will you fit stone worktops I have ordered myself?

Yes, alongside your stone supplier. Stone must be templated and fabricated by the supplier once the base units are fixed and level, so our part is getting the units ready, checking they are sound and reconnecting the sink, tap and hob after the stone is in. Laminate and wood worktops you have bought can be cut, jointed and fitted on site in the usual way.

Kitchen worktop fitting in neighbouring towns

The same service is available a short drive from Cannock, including: