Kitchen worktop fitting · Scotland
Kitchen worktop fitting in Argyll and Bute
We carry out kitchen worktop fitting across Argyll and Bute, from Dunoon to the smaller towns, with a free survey visit and an itemised written quote as standard.
Why kitchen worktop fitting for an Argyll and Bute home?
Some homeowners across Argyll and Bute have already ordered stone worktops from a supplier and need someone to fix and level the base units so templating can go ahead.
Homeowners in Argyll and Bute with sound units but worn, chipped or swollen laminate often replace just the worktops, keeping the rest of the kitchen as it is.
What does kitchen worktop fitting in Argyll and Bute include?
Here is what usually goes into kitchen worktop fitting, adjusted to your Argyll and Bute kitchen after we have measured it:
- Free survey visit to measure the runs and check the base units are level
- Old worktops removed and taken away, with the sink and hob disconnected safely
- Laminate jointed with a mason's mitre or joint strips, and every cut edge sealed
- Solid wood oiled before and after fitting and fixed to allow seasonal movement
- Quartz, granite or sintered stone templated once the base units are fixed and level
- Undermount sink and hob cut-outs cut and finished by the stone fabricator
- Sink, tap and hob reconnected, with gas hobs connected by Gas Safe registered engineers
- Matching upstands fitted and the joint to the wall sealed
How much does kitchen worktop fitting cost in Argyll and Bute?
The figures below are guide prices for Argyll and Bute, including VAT and adjusted for typical costs across Scotland. The fixed price comes after we have measured up. Costs across Scotland tend to sit under UK averages, which these ranges reflect.
| Typical project | Guide price |
|---|---|
| Laminate worktops, supplied and fittedTypical kitchen, joints, cut-outs and upstands | £470–£1,100 |
| Solid wood worktops, supplied and fittedOiled before and after fitting | £850–£1,700 |
| Granite, templated and fittedTemplate visit, cutting, delivery and fitting | £1,400–£3,000 |
| Quartz, templated and fittedTemplate visit, cutting, delivery and fitting | £1,700–£3,300 |
| Old worktops removed and taken awayMore for stone | £80–£240 |
Guide ranges are for a typical kitchen and include the worktops, cut-outs, upstands and fitting; removing old tops is a separate line, and new sinks, taps and splashbacks are priced on top. Prices include VAT at 20%.
Kitchens in homes across Argyll and Bute
The housing mix across Argyll and Bute includes Victorian villas, whitewashed cottages, tenement flats and post-war bungalows, so no two kitchen fits are quite alike. Victorian villas in Dunoon and Oban often have a separate scullery and a larger kitchen, while cottages and bungalows tend to have a compact room at the back.
Soft water is usual across Argyll and Bute, so limescale is rarely a concern, though rural homes on private supplies may need their own filtering. Long single-track roads are common, and some mainland addresses are quickest reached by ferry, so delivery dates, vehicle size and worktop lengths need planning around timetables and weather.
Villa kitchens are sometimes split between a main room and a former scullery, and joining them is a common project that needs a building warrant if the wall is load-bearing. Rural cottages are often off the gas grid, so cooking may be electric or run from LPG.
Rules for kitchen worktop fitting in Argyll and Bute
In Scotland, replacing worktops counts as replacing fitments, so it does not need a building warrant. Any electrical changes, such as new sockets above the worktop, must meet the building standards and BS 7671, and you should ask for an electrical certificate. Gas hobs must be disconnected and reconnected by a Gas Safe registered engineer, and a sink needing a new underground drain connection would need a warrant first.
Parts of Cowal lie within Loch Lomond and The Trossachs National Park, and listed buildings or conservation areas may need consent for a new external vent.
Before you start
- Solid wood needs regular re-oiling and should not be left with standing water around the sink, tap or kettle.
- Stone worktops are templated only once the base units are fixed and level, so allow one to two weeks between fitting and finishing.
- Quartz and granite are heavy; the units must be sound, level and well fixed, and any swollen or weak carcasses replaced first.
- Use trivets for hot pans on every type of worktop; sudden heat can scorch laminate and wood and mark or crack some stone.
- Plan the joint positions before ordering laminate, keeping them away from the sink and dishwasher, where water is most likely to sit.
- Before templating day at your Argyll and Bute home, make sure the sink, tap and hob are on site so the stone can be cut to them.
Questions about kitchen worktop fitting in Argyll and Bute
How much does kitchen worktop fitting cost in Argyll and Bute?
Kitchen worktop fitting in Argyll and Bute typically costs £470 to £1,100 including VAT for laminate worktops, supplied and fitted, based on prices in Scotland. Larger or more involved jobs cost more, and your price is fixed in writing after a free survey visit.
Do you cover the whole of Argyll and Bute?
Yes, across mainland Argyll and Bute, including Dunoon and Oban. We do not currently cover the islands, such as Bute, Mull and Islay. Every job starts with a free survey visit and an itemised written quote.
Will you fit stone worktops I have ordered myself?
Yes, alongside your stone supplier. Stone must be templated and fabricated by the supplier once the base units are fixed and level, so our part is getting the units ready, checking they are sound and reconnecting the sink, tap and hob after the stone is in. Laminate and wood worktops you have bought can be cut, jointed and fitted on site in the usual way.
How long does it take to fit new worktops?
Usually a day for laminate or solid wood in a typical kitchen, cut and jointed on site. Stone takes two visits: the fabricator templates once the base units are fixed and level, then cuts the worktops, the sink and hob openings and any drainer grooves, and fits them about one to two weeks later. In the meantime the sink is usually out of use, so plan meals around that gap.
How are laminate worktops joined at corners?
With either a mason's mitre or a joint strip. A mason's mitre is routed with a jig so the front edge profile turns the corner, then glued, sealed and pulled tight with connector bolts underneath. A joint strip is a metal or colour-matched profile fixed and sealed between the two lengths. Either way, every cut edge, including the sink and hob cut-outs, is sealed so water cannot swell the core.
Kitchen worktop fitting in towns across Argyll and Bute
Choose a town for local guide prices and postcode coverage: