Splashbacks and tiling in Sandy

Thinking about splashbacks and tiling in Sandy?

If the units in your Sandy kitchen are already fitted and only the walls are unfinished, we can take on the tiling or splashback as a job on its own.

Landlords around Bedfordshire often prefer plain tiles with mid-grey grout or a glass panel, since both stand up to heavy use and are quick to clean between tenancies. Our Bedfordshire coverage reaches every part of Sandy (SG19) and out towards Biggleswade.

What is in a typical job?

The exact scope is agreed after the survey, but a typical job in Sandy covers:

Old tiles removed and walls prepared, patched or boarded where needed
Toughened glass splashback measured after the worktops are fitted, with socket cut-outs
Socket and switch plates refitted by an electrician once the tiling is finished
Free survey visit to check the walls, agree the layout and give an itemised quote
Tiled splashbacks between the worktop and wall units, set out from a centre line
Grout and sealant chosen for easy cleaning, with flexible sealant at the worktop joint

What do splashbacks and tiling cost in Sandy?

These guide ranges include VAT at 20% and are adjusted for prices in the East of England. We confirm your price in writing after a free survey visit. Prices in the East of England usually run above the national guide, mainly because labour and parking cost more.

What do splashbacks and tiling cost in Sandy?
Typical project	Guide price
Tiled splashbackBetween worktop and wall units	£160–£430
Kitchen wall tiling, 4–6 m²Preparation, tiling and grouting	£320–£860
Toughened glass splashback behind the hob, fittedMade to measure after the worktops are in	£270–£650
Stone upstands and splashbacksTemplated with the worktop	Priced with the worktop

Tiling guide ranges cover preparation, adhesive, grout, trims and fixing, with the tiles themselves confirmed once chosen; the glass range includes a made-to-measure panel, and stone upstands are priced with the worktop. Prices include VAT at 20%.

Fitting kitchens in older and newer Sandy homes

Typical homes in this part of Bedfordshire include Victorian terraces, 1930s semis, post-war council-built houses and new-build estates. Terraced houses here often have a narrow galley or back-addition kitchen, while interwar semis tend to have a small square kitchen at the rear.

Town-centre terraces can have tight on-street parking, so it helps to plan where a van unloads and how long worktops will pass through a narrow hallway. Water across most of Bedfordshire is hard, so limescale builds up quickly on taps and boiling water taps, and a scale-reducing filter is worth considering.

Building regulations, electrics and gas in Sandy

Tiling or fitting a splashback in England needs no planning permission or building regulations approval. If sockets or switches are moved to suit the new wall finish, that is electrical work to BS 7671; adding to an existing kitchen circuit is not notifiable under Part P, but a new circuit is. Behind a gas hob, follow the hob maker's clearance instructions, and in a listed building, removing historic tiles or panelling may need listed building consent.

Fitting a kitchen needs no planning permission, but listed cottages in the older market towns may need listed building consent for changes such as a new vent through a historic wall.

Getting the most from your splashbacks and tiling

Ask to see where the tiling will start before the first row goes on in your Sandy kitchen, so narrow cut tiles end up in corners rather than on show.
Hold a few of your chosen tiles against the wall in your Sandy kitchen, in daylight and under the kitchen lights, before ordering the full quantity.
Choosing stone worktops for a Sandy kitchen? Ask for upstand and splashback heights to be confirmed before the template visit, not after.
Heavy tiles, such as large porcelain or natural stone, may need a stronger backing board and a suitable adhesive, so have the wall checked first.

Questions about splashbacks and tiling in Sandy

How much do splashbacks and tiling cost in Sandy?

Splashbacks and tiling in Sandy typically cost £160 to £430 including VAT for a tiled splashback, based on prices in the East of England. Larger or more involved jobs cost more, and your price is fixed in writing after a free survey visit.

Which parts of Sandy do you work in?

All of them. Our Bedfordshire coverage takes in the whole of Sandy, including the SG19 postcode district, as well as surrounding towns such as Biggleswade. If you are unsure, send us your postcode.

When are splashbacks fitted during a kitchen installation?

Splashbacks go on near the end, once the worktops are fixed and the electrician has agreed where the sockets and switches will sit. Tiles need a finished worktop to start from, glass is measured off the fitted worktop, and stone upstands are templated at the same visit as the worktop. Faceplates go back on after tiling, so the sockets sit neatly against the new finish.

Can you tile over existing kitchen tiles?

Sometimes, but it is rarely the better choice in a kitchen. Tiling over old tiles adds thickness, so sockets, switches and the edge against the wall units may no longer line up, and the new tiles rely on the old ones staying firmly bonded. If the existing tiles are sound and flat it can work for a small area; otherwise we remove them and prepare the wall.

Can a glass splashback go behind a gas hob?

Yes, usually, as long as the glass is toughened and the hob maker's instructions allow it. Toughened glass handles heat far better than ordinary glass, but a gas hob must still keep the clearances set out in its installation instructions, so we check those before ordering. The panel is measured after the worktops are fitted and made with cut-outs for sockets, because it cannot be cut once toughened.

Splashbacks and tiling in neighbouring towns

The same service is available a short drive from Sandy, including: