Sink and tap installation in Tiverton

Is sink and tap installation right for your Tiverton kitchen?

Homeowners across Devon adding a boiling water tap often need a socket or spur in the sink cupboard, a filter and space for the tank planned in.

People in Tiverton with low water pressure sometimes find a new tap disappointing, so checking the pressure before choosing a tap or boiling water tap saves trouble later. Kitchens in every part of Tiverton are covered, and the survey visit is free wherever you are in Devon.

What does the job involve?

Here is what usually goes into sink and tap installation, adjusted to your Tiverton kitchen after we have measured it:

Inset sink cut-outs made on site in laminate and wood worktops
Isolation valves on the hot and cold supplies, with flexible tap tails connected
New sink fitted, sealed and connected to the existing supplies and waste
Boiling water tap fitted with its tank, filter and power supply in the cupboard
Every joint leak tested, with water flow and drainage checked before handover
Sink moved to a new position with new supply and waste runs

Guide prices for sink and tap installation in Tiverton

Use these ranges to plan your budget. They include VAT, reflect costs in the South West, and are firmed up once we have seen your Tiverton kitchen. For the South West, these ranges are close to the national figures.

Guide prices for sink and tap installation in Tiverton
Typical project	Guide price
Sink and tap plumbed inIsolation valves, waste and trap	£210–£410
Boiling water tap installedTank under the sink, filter and power supply	£150–£360
Sink moved to a new positionNew supplies and waste run	£410–£1,000
Undermount sink in a stone worktopCut-out and polishing are done by the stone fabricator	Priced with the worktop

Guide ranges cover labour and fittings such as valves, tails and wastes; the sink and tap themselves are extra, and undermount cut-outs in stone are priced with the worktop by the fabricator. Prices include VAT at 20%.

Local homes and their kitchens

The housing mix across Devon includes cob and thatched cottages, Victorian terraces, post-war houses and flats and seaside bungalows, so no two kitchen fits are quite alike. Victorian terraces in Exeter and Torbay often have a narrow back kitchen, while post-war houses and seaside bungalows usually have a square room that suits an L-shape.

Single-track lanes, steep town streets and cottages with no parking can make deliveries slow, so long worktops and tall units need a planned route into the house. Much of Devon has soft mains water, which is kind to taps and appliances, though some eastern parts are harder, so check with your supplier.

Building regulations, electrics and gas in Tiverton

Replacing a sink and tap needs no approval in England, but the plumbing should meet the Water Supply (Water Fittings) Regulations 1999, including isolation valves and backflow protection. Connecting to an existing waste is routine, while a new connection to an underground drain involves building control. A new spur for a boiling water tap on an existing kitchen circuit is not notifiable under Part P, but it must meet BS 7671.

Homes within Dartmoor or Exmoor national parks, listed thatched cottages and conservation areas may need consent before a new extractor vent goes through an outside wall.

Before you book sink and tap installation in Tiverton

Choose the sink before stone worktops are templated in your Tiverton kitchen, so the fabricator can cut and polish the undermount opening to suit it.
Find the stopcock in your Tiverton home before the plumber arrives and check it turns off fully, as older stopcocks can stick or let water past.
Check the tap's hole size against the sink or worktop before ordering, as some taps need a larger hole than an existing sink provides.
Moving the sink means new supply and waste runs, so check the waste can fall properly to the drain or stack from the new position.

Questions about sink and tap installation in Tiverton

How much does sink and tap installation cost in Tiverton?

Sink and tap installation in Tiverton typically costs £210 to £410 including VAT for plumbing in a new sink and tap, based on prices in the South West. Larger or more involved jobs cost more, and your price is fixed in writing after a free survey visit.

Can you measure up in Tiverton before quoting?

Yes. Every quote starts with a free, no-obligation survey visit to your home in Tiverton. We measure the room, check the walls, floor and service positions, then send an itemised written quote.

Can a dishwasher and washing machine drain through the sink waste?

Yes, in most kitchens. The sink trap can take an appliance connection on a spigot, or a separate standpipe can be fitted. The appliance hose needs to rise to the height its manufacturer specifies before it drops to the waste, so dirty water cannot siphon back. Two appliances can usually share a double-spigot trap, which we plan with the sink.

What is the difference between an inset and an undermount sink?

An inset sink drops into a cut-out from above, with its rim resting on the worktop, and suits laminate, wood and stone. An undermount sink is fixed beneath the worktop so the edge of the cut-out is exposed, which usually calls for a solid, water-resistant material such as stone or solid surface. Undermount cut-outs in stone are cut and polished by the fabricator.

Do I need isolation valves under my kitchen sink?

They are strongly advised, and we fit them as standard. An isolation valve on each supply to the tap, and on each appliance supply, lets you turn off the water to one fitting without shutting off the whole house. That makes changing a tap cartridge or dealing with a leak far simpler. The valves are left where they can still be reached once the cupboard is in use.

Also covering nearby towns

Neighbouring towns where we offer sink and tap installation: