Sink and tap installation in Gateshead

Thinking about sink and tap installation in Gateshead?

If a new dishwasher or washing machine is going next to the sink in your Gateshead home, the trap and waste connections usually need changing as well.

Landlords in Tyne and Wear often swap tired sinks and taps between tenancies, choosing hard-wearing finishes and accessible valves so that later repairs are quick and cheap. Our Tyne and Wear coverage reaches every part of Gateshead (NE8) and out towards Newcastle upon Tyne.

What does sink and tap installation in Gateshead include?

Every kitchen is different, so we confirm the scope in writing. Most jobs of this kind include:

Every joint leak tested, with water flow and drainage checked before handover
Isolation valves on the hot and cold supplies, with flexible tap tails connected
Sink moved to a new position with new supply and waste runs
New sink fitted, sealed and connected to the existing supplies and waste
Waste, overflow and trap fitted, with dishwasher and washing machine waste connections
Ceramic farmhouse-style sinks set on a suitable supporting base unit and sealed

What does sink and tap installation cost in Gateshead?

Typical sink and tap installation prices for homes in Gateshead, including VAT and adjusted for the North East. Your own figure depends on the size of the kitchen, the layout and what is moving. Labour rates in the North East are generally lower than in London and the South East, so these ranges are a little below the national guide.

What does sink and tap installation cost in Gateshead?
Typical project	Guide price
Sink and tap plumbed inIsolation valves, waste and trap	£180–£360
Boiling water tap installedTank under the sink, filter and power supply	£140–£320
Sink moved to a new positionNew supplies and waste run	£360–£900
Undermount sink in a stone worktopCut-out and polishing are done by the stone fabricator	Priced with the worktop

Guide ranges cover labour and fittings such as valves, tails and wastes; the sink and tap themselves are extra, and undermount cut-outs in stone are priced with the worktop by the fabricator. Prices include VAT at 20%.

Fitting kitchens in older and newer Gateshead homes

Typical homes in this part of Tyne and Wear include tyneside flats, Victorian terraces, 1930s semis and post-war council-built houses. Tyneside flats often have a narrow kitchen in the rear offshoot, while 1930s semis and ex-council houses tend to have a small square kitchen at the back.

Back lanes behind terraced streets can help deliveries, but upper Tyneside flats have their own internal stair, so long worktops need careful handling. Hardness varies across Tyne and Wear, from fairly soft around Newcastle to harder in parts of Sunderland, so check with your supplier before choosing a filter.

Do you need approval for sink and tap installation in Gateshead?

Replacing a sink and tap needs no approval in England, but the plumbing should meet the Water Supply (Water Fittings) Regulations 1999, including isolation valves and backflow protection. Connecting to an existing waste is routine, while a new connection to an underground drain involves building control. A new spur for a boiling water tap on an existing kitchen circuit is not notifiable under Part P, but it must meet BS 7671.

In conservation areas and listed buildings, such as parts of central Newcastle and Tynemouth, a new external vent or changes to historic features may need consent.

Getting the most from your sink and tap installation

Check the tap's hole size against the sink or worktop before ordering, as some taps need a larger hole than an existing sink provides.
Ask for the dishwasher and washing machine hoses to be routed so they cannot kink behind the units once the appliances are pushed back into place.
Ask whether a boiling water tap for your kitchen in Tyne and Wear needs a filter, how often it should be changed and where it will sit in the cupboard.
Moving the sink means new supply and waste runs, so check the waste can fall properly to the drain or stack from the new position.

Questions about sink and tap installation in Gateshead

How much does sink and tap installation cost in Gateshead?

Sink and tap installation in Gateshead typically costs £180 to £360 including VAT for plumbing in a new sink and tap, based on prices in the North East. Larger or more involved jobs cost more, and your price is fixed in writing after a free survey visit.

Can you measure up in Gateshead before quoting?

Yes. Every quote starts with a free, no-obligation survey visit to your home in Gateshead. We measure the room, check the walls, floor and service positions, then send an itemised written quote.

What is the difference between an inset and an undermount sink?

An inset sink drops into a cut-out from above, with its rim resting on the worktop, and suits laminate, wood and stone. An undermount sink is fixed beneath the worktop so the edge of the cut-out is exposed, which usually calls for a solid, water-resistant material such as stone or solid surface. Undermount cut-outs in stone are cut and polished by the fabricator.

What do I need for a boiling water tap?

A boiling water tap needs a tank in the cupboard under the sink, usually a socket or fused spur to power it, and often a filter, particularly where the water is hard. Some models have a minimum water pressure, so check yours before buying. The tap also needs a correctly sized hole in the sink or worktop and enough clear cupboard space for the tank and pipework.

Can a dishwasher and washing machine drain through the sink waste?

Yes, in most kitchens. The sink trap can take an appliance connection on a spigot, or a separate standpipe can be fitted. The appliance hose needs to rise to the height its manufacturer specifies before it drops to the waste, so dirty water cannot siphon back. Two appliances can usually share a double-spigot trap, which we plan with the sink.

Nearby places we cover

The same service is available a short drive from Gateshead, including: