Cooker hood installation in Willesden

Who usually needs cooker hood installation in Willesden?

If your Willesden kitchen has an older open-flued boiler, fitting a stronger hood needs care, as it can affect the flue and should be followed by a spillage test.

A new kitchen in a Willesden home can move the hob away from the old vent, so the hood, the duct run and the wall grille all need rethinking together. Our Greater London coverage reaches every part of Willesden (NW10) and out towards Harlesden.

What is in a typical job?

Here is what usually goes into cooker hood installation, adjusted to your Willesden kitchen after we have measured it:

Island and ceiling hoods fixed into the ceiling structure by two people
Hood fixed at the height set by the hood and hob manufacturers
Power supply connected by an electrician and tested to BS 7671
Core drilling through the outside wall and an external grille fitted and sealed
Spillage test by a Gas Safe registered engineer where an open-flued appliance is present
Survey of the hob position, duct route, outside wall and any open-flued appliance

Cooker hood installation prices in Willesden

Use these ranges to plan your budget. They include VAT, reflect costs in London, and are firmed up once we have seen your Willesden kitchen. Expect costs in London to sit somewhat above UK averages, reflecting local labour rates.

Cooker hood installation prices in Willesden
Typical project	Guide price
Like-for-like cooker hood swapSame position and ducting	£160–£310
New ducted hood through an outside wallCore drilling, ducting run and external grille	£390–£1,200
Island or ceiling hood installedTwo-person install, fixings to the ceiling structure	£390–£820
Recirculating hood fittedNo ducting; carbon filters need replacing	£160–£390

Guide ranges cover fitting and connection with standard ducting through a straightforward wall; long or concealed duct runs, ceiling repairs, new electrical spurs, spillage tests and the hood itself are priced separately. Prices include VAT at 20%.

House types around Willesden and what they mean for a kitchen

The housing mix across Greater London includes Victorian and Edwardian terraces, conversion flats, mansion block flats and 1930s semis, so no two kitchen fits are quite alike. Victorian terraces often have a narrow galley beside the side return, while conversion flats and mansion blocks usually fit the kitchen into a small room or along one living-room wall.

Permit parking, red routes and flats without lifts are common, so parking suspensions, stair carries and lift bookings may need arranging before delivery day. London's mains water is hard, so limescale builds quickly on taps and boiling water taps, and a scale-reducing filter is worth planning in.

What rules apply to cooker hood installation in Willesden?

In England, Approved Document F guidance for kitchen extract is about 30 litres per second from a cooker hood extracting outside, or 60 litres per second from a fan elsewhere in the room. A recirculating hood does not remove moisture, so another means of extract is usually needed. A new vent through the outside wall of a flat may need planning permission and the freeholder's consent, and an open-flued gas appliance in the room calls for a spillage test.

Conservation areas are widespread across London, so a new extractor vent on a front wall may need permission, and leaseholders usually need the freeholder's written consent first.

Getting the most from your cooker hood installation

Before choosing a hood for your Willesden kitchen, find the nearest outside wall to the hob, because the shorter the duct run, the better the extraction.
Choose a hood at least as wide as your hob, and compare its stated extraction rate with the size of the room before you buy.
Check whether your Willesden home has an open-flued boiler or gas fire, and mention it at the survey so a spillage test can be planned.
Keep the duct run short and straight with rigid ducting, because every bend and extra metre of flexible hose reduces how much air the hood moves.

Questions about cooker hood installation in Willesden

How much does cooker hood installation cost in Willesden?

Cooker hood installation in Willesden typically costs £160 to £310 including VAT for a like-for-like cooker hood swap, based on prices in London. Larger or more involved jobs cost more, and your price is fixed in writing after a free survey visit.

Do you cover all of Willesden?

Yes. We work across Willesden, including the NW10 postcode district, and nearby towns such as Harlesden and Notting Hill. Book a free survey visit and we will arrange a time that suits you.

Can a ducted cooker hood be fitted in a flat?

Often, but check consents first. A new vent through the outside wall of a flat may need planning permission and the freeholder's written consent, and some leases do not allow it at all. Where an outside vent is not possible, a recirculating hood can be fitted, with a separate extract fan or other ventilation dealing with moisture. Listed buildings may also need listed building consent.

Why might a cooker hood need a spillage test?

Because a hood pulling air out of a room can draw fumes back down the flue of an open-flued gas appliance, such as some older boilers or gas fires. Where the kitchen, or a room open to it, has one, a Gas Safe registered engineer should carry out a spillage test with the hood running at full speed. Room-sealed boilers are not affected in the same way.

Does a cooker hood need a hole in the wall?

A ducted hood does. The usual route is a core-drilled hole through the nearest outside wall, with rigid ducting from the hood and an external grille sealed into the wall. Where the hob is far from an outside wall, the duct can sometimes run above the wall units or through a ceiling void. A recirculating hood needs no hole, but it removes no moisture.

Nearby places we cover

Neighbouring towns where we offer cooker hood installation: