Cooker hood installation in Atherton

Why cooker hood installation for an Atherton home?

Cooks across Greater Manchester who fry, grill or stir-fry often find a recirculating hood leaves smells in the house, and look at ducting the air outside instead.

If your Atherton kitchen has an older open-flued boiler, fitting a stronger hood needs care, as it can affect the flue and should be followed by a spillage test. We work throughout Atherton (M46) and across the wider Greater Manchester area.

What does the job involve?

After the survey visit we write the scope down. For cooker hood installation in Atherton it usually covers:

Survey of the hob position, duct route, outside wall and any open-flued appliance
Island and ceiling hoods fixed into the ceiling structure by two people
Recirculating hoods fitted with carbon filters, and their limits explained
Hood fixed at the height set by the hood and hob manufacturers
Spillage test by a Gas Safe registered engineer where an open-flued appliance is present
Power supply connected by an electrician and tested to BS 7671

Guide prices for cooker hood installation in Atherton

The figures below are guide prices for Atherton, including VAT and adjusted for typical costs across the North West. The fixed price comes after we have measured up. Prices in the North West usually come in below the national guide, as labour rates are lower than in the South East.

Guide prices for cooker hood installation in Atherton
Typical project	Guide price
Like-for-like cooker hood swapSame position and ducting	£110–£230
New ducted hood through an outside wallCore drilling, ducting run and external grille	£280–£860
Island or ceiling hood installedTwo-person install, fixings to the ceiling structure	£280–£600
Recirculating hood fittedNo ducting; carbon filters need replacing	£110–£280

Guide ranges cover fitting and connection with standard ducting through a straightforward wall; long or concealed duct runs, ceiling repairs, new electrical spurs, spillage tests and the hood itself are priced separately. Prices include VAT at 20%.

Fitting kitchens in older and newer Atherton homes

You will find Victorian terraces, 1930s semis, converted mill and warehouse flats and post-war estate houses throughout Greater Manchester. Two-up two-down terraces often have a small back kitchen or a galley in the rear outrigger, while 1930s semis usually have a separate kitchen beside the dining room.

Mains water across Greater Manchester is mostly soft, so limescale is less of a problem and taps and boiling water taps tend to stay cleaner. Terraced streets with back alleys, city-centre flats with booked lifts and permit parking can all affect delivery timing and how long worktops are carried in.

Building regulations, electrics and gas in Atherton

In England, Approved Document F guidance for kitchen extract is about 30 litres per second from a cooker hood extracting outside, or 60 litres per second from a fan elsewhere in the room. A recirculating hood does not remove moisture, so another means of extract is usually needed. A new vent through the outside wall of a flat may need planning permission and the freeholder's consent, and an open-flued gas appliance in the room calls for a spillage test.

Listed mill conversions and homes in conservation areas may need consent for new external vents, and apartment owners usually need the freeholder's or managing agent's consent.

Worth knowing before the fit

Before choosing a hood for your Atherton kitchen, find the nearest outside wall to the hob, because the shorter the duct run, the better the extraction.
Choose a hood at least as wide as your hob, and compare its stated extraction rate with the size of the room before you buy.
Check whether your Atherton home has an open-flued boiler or gas fire, and mention it at the survey so a spillage test can be planned.
Check the minimum height above the hob in both the hood and hob instructions, and use the greater of the two figures.

Questions about cooker hood installation in Atherton

How much does cooker hood installation cost in Atherton?

For a like-for-like cooker hood swap, budget around £110 to £230 including VAT in Atherton. That reflects typical costs in the North West; we confirm the actual figure in writing once we have measured up.

Do you cover all of Atherton?

Yes. We work across Atherton, including the M46 postcode district, and nearby towns such as Tyldesley and Westhoughton. Book a free survey visit and we will arrange a time that suits you.

Does a cooker hood need a hole in the wall?

A ducted hood does. The usual route is a core-drilled hole through the nearest outside wall, with rigid ducting from the hood and an external grille sealed into the wall. Where the hob is far from an outside wall, the duct can sometimes run above the wall units or through a ceiling void. A recirculating hood needs no hole, but it removes no moisture.

Can a ducted cooker hood be fitted in a flat?

Often, but check consents first. A new vent through the outside wall of a flat may need planning permission and the freeholder's written consent, and some leases do not allow it at all. Where an outside vent is not possible, a recirculating hood can be fitted, with a separate extract fan or other ventilation dealing with moisture. Listed buildings may also need listed building consent.

Why might a cooker hood need a spillage test?

Because a hood pulling air out of a room can draw fumes back down the flue of an open-flued gas appliance, such as some older boilers or gas fires. Where the kitchen, or a room open to it, has one, a Gas Safe registered engineer should carry out a spillage test with the hood running at full speed. Room-sealed boilers are not affected in the same way.

Also covering nearby towns

We also carry out cooker hood installation in these towns near Atherton: