Utility room fitting in Slough

Why do people in Slough choose utility room fitting?

In a Slough house where the garage is already used for storage rather than the car, some people fit a run of units and the laundry along one wall.

Dog owners and keen walkers around Slough often ask for a utility with a deep sink, a coat cupboard and somewhere to leave muddy boots and wet jackets. We work throughout Slough (SL1) and across the wider Berkshire area.

What we cover for utility room fitting in Slough

Here is what usually goes into utility room fitting, adjusted to your Slough kitchen after we have measured it:

Stacking kit fitted where the washer and dryer sit one above the other
A vent to outside for a vented dryer, or a drain hose for condenser models
Base, wall and tall units fitted, levelled and fixed to the wall
Utility sink and tap plumbed in, with new supplies and waste where none exist
Free survey visit to check water, waste, power and outside wall positions
Washing machine supply, waste and isolation valve, tested for leaks

What does utility room fitting cost in Slough?

As a starting point for Slough, these ranges include VAT at 20% and allow for typical labour costs in the South East. Labour in the South East generally costs more than the UK average, which lifts these ranges a little.

What does utility room fitting cost in Slough?
Typical project	Guide price
Utility units and worktop fitted (fit only)Three to six units, laminate worktop, panels	£1,400–£3,400
Utility room supplied and fittedUnits, worktop, sink, washer and dryer connections	£3,400–£8,000
New utility plumbing for a sink and washing machineSupplies, waste and valves where none exist	£460–£1,200

Fit-only and supply-and-fit ranges cover units, worktop and standard sink and appliance connections, with new plumbing where none exists as a separate line; extract fans, dryer vents and new circuits are quoted on top. Prices include VAT at 20%.

Local homes and their kitchens

The housing mix across Berkshire includes Victorian and Edwardian terraces, 1930s semis, post-war estate houses and new-build town houses, so no two kitchen fits are quite alike. Edwardian terraces often have a long galley running back from the dining room, while newer three-storey town houses usually have a compact kitchen on the ground floor.

Expect hard water in most of Berkshire, much of it drawn from chalk, so limescale on taps is common and a boiling water tap benefits from a filter. Busy town-centre streets and permit parking zones can make unloading slow, so a parking permit or bay suspension may need arranging before delivery day.

Do you need approval for utility room fitting in Slough?

Fitting a utility room needs no planning permission in England, though a new dryer vent through the outside wall of a flat may need planning permission and the freeholder's consent. Adding sockets to an existing circuit is not notifiable, but a new circuit is, under Part P. Approved Document F sets an extract rate of about 30 litres per second for a utility room, so a new fan should be sized to meet it, and if an open-flued boiler shares the room, a Gas Safe registered engineer should carry out a spillage test once a fan is fitted.

A new extractor vent on a street-facing wall can need permission in a conservation area, and listed homes may need consent for internal changes affecting historic features.

Worth knowing before the fit

If your Berkshire home has an open-flued boiler in the utility, ask for a spillage test by a Gas Safe registered engineer once an extract fan goes in.
Plan the sockets in your Slough utility so each appliance can be switched off at an accessible switch without moving the machine.
In a Slough flat, check with the freeholder before a new dryer vent or extract fan is cut through an outside wall.
A worktop over appliances needs support at each side and a gap above the machines, so they can be slid out for servicing.

Questions about utility room fitting in Slough

How much does utility room fitting cost in Slough?

For fitting three to six utility units and a worktop you have bought, budget around £1,400 to £3,400 including VAT in Slough. That reflects typical costs in the South East; we confirm the actual figure in writing once we have measured up.

Can you measure up in Slough before quoting?

Yes. Every quote starts with a free, no-obligation survey visit to your home in Slough. We measure the room, check the walls, floor and service positions, then send an itemised written quote.

Can a worktop go over a washing machine and dryer?

Yes, and it is one of the most common utility layouts. The worktop is supported by units, end panels or a rail at each side rather than resting on the machines, with a small gap above them for vibration and so they can be slid out for servicing. Standard front-loading machines usually fit under a standard-height worktop, but we check the appliance heights against the plan first.

Does a utility room need an extractor fan?

Yes, in most cases. Washing and drying put a lot of moisture into a small space, so extract ventilation is strongly advised: Approved Document F sets a rate of about 30 litres per second for utility rooms in England and Wales, and the building standards in Scotland and Technical Booklet K in Northern Ireland cover ventilation too. An extract fan ducted outside is the usual answer, with a window helping but not replacing it. A vented dryer needs its own duct as well.

Does a condenser or heat pump dryer need an outside vent?

No. Condenser and heat pump dryers do not need an outside vent, so they can go where a vented dryer cannot. They collect water in a container that has to be emptied, or they can be connected to the waste so they drain automatically, which is easy when the dryer sits beside the washing machine. They still give off some warmth, so the space needs air around it. A vented dryer needs a duct to an outside wall.

Utility room fitting in neighbouring towns

Close to Slough? We cover these nearby towns too: