Utility room fitting · England
Utility room fitting in Shropshire
Our utility room fitting work covers the whole of Shropshire, including Telford, Shrewsbury and Wellington.
What prompts utility room fitting in Shropshire?
Landlords letting larger family homes across Shropshire sometimes add a utility so tenants have room for laundry, coats and cleaning kit without filling the kitchen with appliances.
If your Shropshire home has a back lobby or a rear porch with a little spare width, a few units and a stacked washer and dryer can make it a working utility.
What does utility room fitting in Shropshire include?
Every kitchen is different, so we confirm the scope in writing. Most jobs of this kind include:
- Free survey visit to check water, waste, power and outside wall positions
- Base, wall and tall units fitted, levelled and fixed to the wall
- Worktop over the washing machine and dryer, supported clear of the appliances
- Washing machine supply, waste and isolation valve, tested for leaks
- A vent to outside for a vented dryer, or a drain hose for condenser models
- Stacking kit fitted where the washer and dryer sit one above the other
- Utility sink and tap plumbed in, with new supplies and waste where none exist
- Extract fan fitted to clear moisture from washing and drying
How much does utility room fitting cost in Shropshire?
The figures below are guide prices for Shropshire, including VAT and adjusted for typical costs across the West Midlands. The fixed price comes after we have measured up. Prices across the West Midlands are broadly in line with UK averages.
| Typical project | Guide price |
|---|---|
| Utility units and worktop fitted (fit only)Three to six units, laminate worktop, panels | £1,200–£3,000 |
| Utility room supplied and fittedUnits, worktop, sink, washer and dryer connections | £3,000–£7,000 |
| New utility plumbing for a sink and washing machineSupplies, waste and valves where none exist | £400–£1,000 |
Fit-only and supply-and-fit ranges cover units, worktop and standard sink and appliance connections, with new plumbing where none exists as a separate line; extract fans, dryer vents and new circuits are quoted on top. Prices include VAT at 20%.
Kitchens in homes across Shropshire
You will find timber-framed cottages, Victorian terraces, post-war new town houses and farmhouses throughout Shropshire. Telford's new-town houses often have a compact galley or L-shaped kitchen, while older cottages in Shrewsbury and Ludlow may have small rooms with low beams.
Much of Shropshire has moderately hard to hard water, so limescale on taps and boiling water taps is worth planning for; check with your supplier. Rural lanes, farm tracks and medieval town centres with restricted parking can all complicate deliveries, so vehicle size and timing are planned in advance.
Telford's new-town houses often have small original kitchens, so owners may remove a partition to open them into the dining area. Rural farmhouses and cottages are frequently off the gas grid, so cooking may run on LPG, an oil-fired range or all-electric induction.
Rules for utility room fitting in Shropshire
Fitting a utility room needs no planning permission in England, though a new dryer vent through the outside wall of a flat may need planning permission and the freeholder's consent. Adding sockets to an existing circuit is not notifiable, but a new circuit is, under Part P. Approved Document F sets an extract rate of about 30 litres per second for a utility room, so a new fan should be sized to meet it, and if an open-flued boiler shares the room, a Gas Safe registered engineer should carry out a spillage test once a fan is fitted.
Shrewsbury and Ludlow have many listed timber-framed buildings and conservation areas, so new vents or internal alterations may need listed building consent or planning permission.
Before you start
- Check which dryer you have: a vented dryer needs a duct to an outside wall, while condenser and heat pump dryers need emptying or a drain.
- Under-stairs spaces can take a washer and dryer, but check the headroom, the ventilation and room to pull machines out before committing.
- If there is no water or waste in the space, new plumbing has to reach it, which is simplest close to an existing kitchen or bathroom.
- Stacking the dryer on the washing machine saves width, but it needs a stacking kit that suits both machines and enough height for the pair.
- If the utility will be in the garage of your Shropshire home, make sure the space stays above freezing in winter for the pipes and machines.
- Measure the washer and dryer heights, including any stacking kit, before ordering wall units or shelves to go above them.
Questions about utility room fitting in Shropshire
How much does utility room fitting cost in Shropshire?
For fitting three to six utility units and a worktop you have bought, budget around £1,200 to £3,000 including VAT in Shropshire. That reflects typical costs in the West Midlands; we confirm the actual figure in writing once we have measured up.
Do you cover the whole of Shropshire?
Yes. We carry out utility room fitting across Shropshire, including Telford, Shrewsbury, Wellington and Oswestry. Every job starts with a free survey visit and an itemised written quote.
Does a condenser or heat pump dryer need an outside vent?
No. Condenser and heat pump dryers do not need an outside vent, so they can go where a vented dryer cannot. They collect water in a container that has to be emptied, or they can be connected to the waste so they drain automatically, which is easy when the dryer sits beside the washing machine. They still give off some warmth, so the space needs air around it. A vented dryer needs a duct to an outside wall.
Can a worktop go over a washing machine and dryer?
Yes, and it is one of the most common utility layouts. The worktop is supported by units, end panels or a rail at each side rather than resting on the machines, with a small gap above them for vibration and so they can be slid out for servicing. Standard front-loading machines usually fit under a standard-height worktop, but we check the appliance heights against the plan first.
Can a utility room go in a garage or under the stairs?
Often, yes, as long as the space already exists and is usable. In a garage it needs to be dry and protected from frost, with power and a route for water and waste. Under the stairs, check the headroom, the ventilation and whether a door can open fully. We fit units and connect appliances in existing spaces; converting a garage into a habitable room is a separate building project.
Utility room fitting in towns across Shropshire
Choose a town for local guide prices and postcode coverage:
- Utility room fitting in Telford
- Utility room fitting in Shrewsbury
- Utility room fitting in Wellington
- Utility room fitting in Oswestry
- Utility room fitting in Bridgnorth
- Utility room fitting in Market Drayton
- Utility room fitting in Ludlow
- Utility room fitting in Whitchurch, Shropshire