Utility room fitting in Salford

Why utility room fitting for a Salford home?

When a new kitchen is being planned in Greater Manchester, moving the laundry to a utility often makes room for deep drawers or a dishwasher in the kitchen itself.

Dog owners and keen walkers around Salford often ask for a utility with a deep sink, a coat cupboard and somewhere to leave muddy boots and wet jackets. If your home is in Salford or close by in Eccles or Manchester, the same survey, quote and fitting process applies.

What does utility room fitting in Salford include?

The exact scope is agreed after the survey, but a typical job in Salford covers:

Utility sink and tap plumbed in, with new supplies and waste where none exist
Washing machine supply, waste and isolation valve, tested for leaks
Stacking kit fitted where the washer and dryer sit one above the other
A vent to outside for a vented dryer, or a drain hose for condenser models
Worktop over the washing machine and dryer, supported clear of the appliances
Free survey visit to check water, waste, power and outside wall positions

What should you budget for utility room fitting in Salford?

Typical utility room fitting prices for homes in Salford, including VAT and adjusted for the North West. Your own figure depends on the size of the kitchen, the layout and what is moving. Labour rates in the North West are generally lower than in London and the South East, so these ranges are a little below the national guide.

What should you budget for utility room fitting in Salford?
Typical project	Guide price
Utility units and worktop fitted (fit only)Three to six units, laminate worktop, panels	£1,100–£2,800
Utility room supplied and fittedUnits, worktop, sink, washer and dryer connections	£2,800–£6,600
New utility plumbing for a sink and washing machineSupplies, waste and valves where none exist	£380–£950

Fit-only and supply-and-fit ranges cover units, worktop and standard sink and appliance connections, with new plumbing where none exists as a separate line; extract fans, dryer vents and new circuits are quoted on top. Prices include VAT at 20%.

What kind of kitchens do we fit in Salford?

Across Greater Manchester you will often find Victorian terraces, 1930s semis, converted mill and warehouse flats and post-war estate houses, and each shapes the kitchen differently. Two-up two-down terraces often have a small back kitchen or a galley in the rear outrigger, while 1930s semis usually have a separate kitchen beside the dining room.

Terraced streets with back alleys, city-centre flats with booked lifts and permit parking can all affect delivery timing and how long worktops are carried in. Mains water across Greater Manchester is mostly soft, so limescale is less of a problem and taps and boiling water taps tend to stay cleaner.

Building regulations, electrics and gas in Salford

Fitting a utility room needs no planning permission in England, though a new dryer vent through the outside wall of a flat may need planning permission and the freeholder's consent. Adding sockets to an existing circuit is not notifiable, but a new circuit is, under Part P. Approved Document F sets an extract rate of about 30 litres per second for a utility room, so a new fan should be sized to meet it, and if an open-flued boiler shares the room, a Gas Safe registered engineer should carry out a spillage test once a fan is fitted.

Listed mill conversions and homes in conservation areas may need consent for new external vents, and apartment owners usually need the freeholder's or managing agent's consent.

Planning ahead

In a Salford flat, check with the freeholder before a new dryer vent or extract fan is cut through an outside wall.
If your Greater Manchester home has an open-flued boiler in the utility, ask for a spillage test by a Gas Safe registered engineer once an extract fan goes in.
Plan the sockets in your Salford utility so each appliance can be switched off at an accessible switch without moving the machine.
A utility in a garage needs to be dry, lit and kept above freezing already; converting the garage itself is a separate building job.

Questions about utility room fitting in Salford

How much does utility room fitting cost in Salford?

Guide prices in Salford are about £1,100 to £2,800 including VAT for fitting three to six utility units and a worktop you have bought. The final price depends on the size of the kitchen and what is moving, and is set out in an itemised written quote.

Can you measure up in Salford before quoting?

Yes. Every quote starts with a free, no-obligation survey visit to your home in Salford. We measure the room, check the walls, floor and service positions, then send an itemised written quote.

Can a utility room go in a garage or under the stairs?

Often, yes, as long as the space already exists and is usable. In a garage it needs to be dry and protected from frost, with power and a route for water and waste. Under the stairs, check the headroom, the ventilation and whether a door can open fully. We fit units and connect appliances in existing spaces; converting a garage into a habitable room is a separate building project.

Does a condenser or heat pump dryer need an outside vent?

No. Condenser and heat pump dryers do not need an outside vent, so they can go where a vented dryer cannot. They collect water in a container that has to be emptied, or they can be connected to the waste so they drain automatically, which is easy when the dryer sits beside the washing machine. They still give off some warmth, so the space needs air around it. A vented dryer needs a duct to an outside wall.

Can a worktop go over a washing machine and dryer?

Yes, and it is one of the most common utility layouts. The worktop is supported by units, end panels or a rail at each side rather than resting on the machines, with a small gap above them for vibration and so they can be slid out for servicing. Standard front-loading machines usually fit under a standard-height worktop, but we check the appliance heights against the plan first.

Utility room fitting near Salford

Neighbouring towns where we offer utility room fitting: