Utility room fitting in Golders Green

Is utility room fitting right for your Golders Green kitchen?

If your Golders Green home has a back lobby or a rear porch with a little spare width, a few units and a stacked washer and dryer can make it a working utility.

Dog owners and keen walkers around Golders Green often ask for a utility with a deep sink, a coat cupboard and somewhere to leave muddy boots and wet jackets. Golders Green sits about 6 miles north-west of Westminster, and our Greater London coverage takes in everything in between.

What we cover for utility room fitting in Golders Green

After the survey visit we write the scope down. For utility room fitting in Golders Green it usually covers:

Stacking kit fitted where the washer and dryer sit one above the other
Base, wall and tall units fitted, levelled and fixed to the wall
Washing machine supply, waste and isolation valve, tested for leaks
Worktop over the washing machine and dryer, supported clear of the appliances
A vent to outside for a vented dryer, or a drain hose for condenser models
Free survey visit to check water, waste, power and outside wall positions

What does utility room fitting cost in Golders Green?

As a starting point for Golders Green, these ranges include VAT at 20% and allow for typical labour costs in London. Labour in London generally costs more than the UK average, which lifts these ranges a little.

What does utility room fitting cost in Golders Green?
Typical project	Guide price
Utility units and worktop fitted (fit only)Three to six units, laminate worktop, panels	£1,600–£3,900
Utility room supplied and fittedUnits, worktop, sink, washer and dryer connections	£3,900–£9,100
New utility plumbing for a sink and washing machineSupplies, waste and valves where none exist	£520–£1,300

Fit-only and supply-and-fit ranges cover units, worktop and standard sink and appliance connections, with new plumbing where none exists as a separate line; extract fans, dryer vents and new circuits are quoted on top. Prices include VAT at 20%.

Kitchens in homes around Golders Green

The housing mix across Greater London includes Victorian and Edwardian terraces, conversion flats, mansion block flats and 1930s semis, so no two kitchen fits are quite alike. Victorian terraces often have a narrow galley beside the side return, while conversion flats and mansion blocks usually fit the kitchen into a small room or along one living-room wall.

London's mains water is hard, so limescale builds quickly on taps and boiling water taps, and a scale-reducing filter is worth planning in. Permit parking, red routes and flats without lifts are common, so parking suspensions, stair carries and lift bookings may need arranging before delivery day.

Regulations for kitchen work in Golders Green

Fitting a utility room needs no planning permission in England, though a new dryer vent through the outside wall of a flat may need planning permission and the freeholder's consent. Adding sockets to an existing circuit is not notifiable, but a new circuit is, under Part P. Approved Document F sets an extract rate of about 30 litres per second for a utility room, so a new fan should be sized to meet it, and if an open-flued boiler shares the room, a Gas Safe registered engineer should carry out a spillage test once a fan is fitted.

Conservation areas are widespread across London, so a new extractor vent on a front wall may need permission, and leaseholders usually need the freeholder's written consent first.

Planning ahead

In a Golders Green flat, check with the freeholder before a new dryer vent or extract fan is cut through an outside wall.
Before choosing a dryer for your Golders Green utility, check whether there is an outside wall close enough for a short, straight vent duct.
Ask for an isolation valve on the washing machine supply that can be reached without pulling the machine out from under the worktop.
A utility in a garage needs to be dry, lit and kept above freezing already; converting the garage itself is a separate building job.

Questions about utility room fitting in Golders Green

How much does utility room fitting cost in Golders Green?

Utility room fitting in Golders Green typically costs £1,600 to £3,900 including VAT for fitting three to six utility units and a worktop you have bought, based on prices in London. Larger or more involved jobs cost more, and your price is fixed in writing after a free survey visit.

Do you work near Golders Green as well?

Yes. As well as Golders Green itself, we cover the rest of Greater London and nearby towns such as Kilburn and Finchley. The process is the same wherever the kitchen is.

Can a utility room go in a garage or under the stairs?

Often, yes, as long as the space already exists and is usable. In a garage it needs to be dry and protected from frost, with power and a route for water and waste. Under the stairs, check the headroom, the ventilation and whether a door can open fully. We fit units and connect appliances in existing spaces; converting a garage into a habitable room is a separate building project.

Can a worktop go over a washing machine and dryer?

Yes, and it is one of the most common utility layouts. The worktop is supported by units, end panels or a rail at each side rather than resting on the machines, with a small gap above them for vibration and so they can be slid out for servicing. Standard front-loading machines usually fit under a standard-height worktop, but we check the appliance heights against the plan first.

Does a condenser or heat pump dryer need an outside vent?

No. Condenser and heat pump dryers do not need an outside vent, so they can go where a vented dryer cannot. They collect water in a container that has to be emptied, or they can be connected to the waste so they drain automatically, which is easy when the dryer sits beside the washing machine. They still give off some warmth, so the space needs air around it. A vented dryer needs a duct to an outside wall.

Also covering nearby towns

Neighbouring towns where we offer utility room fitting: