Utility room fitting in Edmonton

Why do people in Edmonton choose utility room fitting?

When a new kitchen is being planned in Greater London, moving the laundry to a utility often makes room for deep drawers or a dishwasher in the kitchen itself.

If the kitchen in your Greater London home is a narrow galley, a separate utility can take the appliances that would otherwise crowd the worktop and storage. We cover all of Edmonton, including the N18 postcode district, and travel out to neighbouring towns across Greater London.

What is included in the work?

After the survey visit we write the scope down. For utility room fitting in Edmonton it usually covers:

Stacking kit fitted where the washer and dryer sit one above the other
Base, wall and tall units fitted, levelled and fixed to the wall
Free survey visit to check water, waste, power and outside wall positions
Extract fan fitted to clear moisture from washing and drying
Utility sink and tap plumbed in, with new supplies and waste where none exist
A vent to outside for a vented dryer, or a drain hose for condenser models

Utility room fitting prices in Edmonton

Use these ranges to plan your budget. They include VAT, reflect costs in London, and are firmed up once we have seen your Edmonton kitchen. Expect costs in London to sit somewhat above UK averages, reflecting local labour rates.

Utility room fitting prices in Edmonton
Typical project	Guide price
Utility units and worktop fitted (fit only)Three to six units, laminate worktop, panels	£1,600–£3,900
Utility room supplied and fittedUnits, worktop, sink, washer and dryer connections	£3,900–£9,100
New utility plumbing for a sink and washing machineSupplies, waste and valves where none exist	£520–£1,300

Fit-only and supply-and-fit ranges cover units, worktop and standard sink and appliance connections, with new plumbing where none exists as a separate line; extract fans, dryer vents and new circuits are quoted on top. Prices include VAT at 20%.

Kitchens in homes around Edmonton

You will find Victorian and Edwardian terraces, conversion flats, mansion block flats and 1930s semis throughout Greater London. Victorian terraces often have a narrow galley beside the side return, while conversion flats and mansion blocks usually fit the kitchen into a small room or along one living-room wall.

London's mains water is hard, so limescale builds quickly on taps and boiling water taps, and a scale-reducing filter is worth planning in. Permit parking, red routes and flats without lifts are common, so parking suspensions, stair carries and lift bookings may need arranging before delivery day.

Regulations for kitchen work in Edmonton

Fitting a utility room needs no planning permission in England, though a new dryer vent through the outside wall of a flat may need planning permission and the freeholder's consent. Adding sockets to an existing circuit is not notifiable, but a new circuit is, under Part P. Approved Document F sets an extract rate of about 30 litres per second for a utility room, so a new fan should be sized to meet it, and if an open-flued boiler shares the room, a Gas Safe registered engineer should carry out a spillage test once a fan is fitted.

Conservation areas are widespread across London, so a new extractor vent on a front wall may need permission, and leaseholders usually need the freeholder's written consent first.

Worth knowing before the fit

Plan the sockets in your Edmonton utility so each appliance can be switched off at an accessible switch without moving the machine.
In an Edmonton flat, check with the freeholder before a new dryer vent or extract fan is cut through an outside wall.
Measure the washer and dryer heights, including any stacking kit, before ordering wall units or shelves to go above them.
A utility in a garage needs to be dry, lit and kept above freezing already; converting the garage itself is a separate building job.

Questions about utility room fitting in Edmonton

How much does utility room fitting cost in Edmonton?

Utility room fitting in Edmonton typically costs £1,600 to £3,900 including VAT for fitting three to six utility units and a worktop you have bought, based on prices in London. Larger or more involved jobs cost more, and your price is fixed in writing after a free survey visit.

Do you work near Edmonton as well?

Yes. As well as Edmonton itself, we cover the rest of Greater London and nearby towns such as Tottenham and Enfield. The process is the same wherever the kitchen is.

Does a utility room need an extractor fan?

Yes, in most cases. Washing and drying put a lot of moisture into a small space, so extract ventilation is strongly advised: Approved Document F sets a rate of about 30 litres per second for utility rooms in England and Wales, and the building standards in Scotland and Technical Booklet K in Northern Ireland cover ventilation too. An extract fan ducted outside is the usual answer, with a window helping but not replacing it. A vented dryer needs its own duct as well.

Can a worktop go over a washing machine and dryer?

Yes, and it is one of the most common utility layouts. The worktop is supported by units, end panels or a rail at each side rather than resting on the machines, with a small gap above them for vibration and so they can be slid out for servicing. Standard front-loading machines usually fit under a standard-height worktop, but we check the appliance heights against the plan first.

Can a utility room go in a garage or under the stairs?

Often, yes, as long as the space already exists and is usable. In a garage it needs to be dry and protected from frost, with power and a route for water and waste. Under the stairs, check the headroom, the ventilation and whether a door can open fully. We fit units and connect appliances in existing spaces; converting a garage into a habitable room is a separate building project.

Utility room fitting in neighbouring towns

We also carry out utility room fitting in these towns near Edmonton: