Utility room fitting in Bolton

Why do people in Bolton choose utility room fitting?

Larger households in Bolton sharing a lot of laundry often want a stacked washer and dryer, a hanging rail and a clear worktop for folding.

If the kitchen in your Greater Manchester home is a narrow galley, a separate utility can take the appliances that would otherwise crowd the worktop and storage. Bolton sits about 11 miles north-west of Manchester, and our Greater Manchester coverage takes in everything in between.

What is included in the work?

Here is what usually goes into utility room fitting, adjusted to your Bolton kitchen after we have measured it:

Worktop over the washing machine and dryer, supported clear of the appliances
Extract fan fitted to clear moisture from washing and drying
Washing machine supply, waste and isolation valve, tested for leaks
Free survey visit to check water, waste, power and outside wall positions
Base, wall and tall units fitted, levelled and fixed to the wall
Utility sink and tap plumbed in, with new supplies and waste where none exist

Utility room fitting prices in Bolton

Typical utility room fitting prices for homes in Bolton, including VAT and adjusted for the North West. Your own figure depends on the size of the kitchen, the layout and what is moving. Labour rates in the North West are generally lower than in London and the South East, so these ranges are a little below the national guide.

Utility room fitting prices in Bolton
Typical project	Guide price
Utility units and worktop fitted (fit only)Three to six units, laminate worktop, panels	£1,100–£2,800
Utility room supplied and fittedUnits, worktop, sink, washer and dryer connections	£2,800–£6,600
New utility plumbing for a sink and washing machineSupplies, waste and valves where none exist	£380–£950

Fit-only and supply-and-fit ranges cover units, worktop and standard sink and appliance connections, with new plumbing where none exists as a separate line; extract fans, dryer vents and new circuits are quoted on top. Prices include VAT at 20%.

House types around Bolton and what they mean for a kitchen

You will find Victorian terraces, 1930s semis, converted mill and warehouse flats and post-war estate houses throughout Greater Manchester. Two-up two-down terraces often have a small back kitchen or a galley in the rear outrigger, while 1930s semis usually have a separate kitchen beside the dining room.

Terraced streets with back alleys, city-centre flats with booked lifts and permit parking can all affect delivery timing and how long worktops are carried in. Mains water across Greater Manchester is mostly soft, so limescale is less of a problem and taps and boiling water taps tend to stay cleaner.

Regulations for kitchen work in Bolton

Fitting a utility room needs no planning permission in England, though a new dryer vent through the outside wall of a flat may need planning permission and the freeholder's consent. Adding sockets to an existing circuit is not notifiable, but a new circuit is, under Part P. Approved Document F sets an extract rate of about 30 litres per second for a utility room, so a new fan should be sized to meet it, and if an open-flued boiler shares the room, a Gas Safe registered engineer should carry out a spillage test once a fan is fitted.

Listed mill conversions and homes in conservation areas may need consent for new external vents, and apartment owners usually need the freeholder's or managing agent's consent.

Practical advice for Bolton homeowners

If your Greater Manchester home has an open-flued boiler in the utility, ask for a spillage test by a Gas Safe registered engineer once an extract fan goes in.
Leave room behind the washing machine for the hoses; pushing it hard against the wall can kink them and stop the water draining properly.
If the utility will be in the garage of your Bolton home, make sure the space stays above freezing in winter for the pipes and machines.
Under-stairs spaces can take a washer and dryer, but check the headroom, the ventilation and room to pull machines out before committing.

Questions about utility room fitting in Bolton

How much does utility room fitting cost in Bolton?

Guide prices in Bolton are about £1,100 to £2,800 including VAT for fitting three to six utility units and a worktop you have bought. The final price depends on the size of the kitchen and what is moving, and is set out in an itemised written quote.

Do you work near Bolton as well?

Yes. As well as Bolton itself, we cover the rest of Greater Manchester and nearby towns such as Farnworth and Westhoughton. The process is the same wherever the kitchen is.

Does a condenser or heat pump dryer need an outside vent?

No. Condenser and heat pump dryers do not need an outside vent, so they can go where a vented dryer cannot. They collect water in a container that has to be emptied, or they can be connected to the waste so they drain automatically, which is easy when the dryer sits beside the washing machine. They still give off some warmth, so the space needs air around it. A vented dryer needs a duct to an outside wall.

Can a worktop go over a washing machine and dryer?

Yes, and it is one of the most common utility layouts. The worktop is supported by units, end panels or a rail at each side rather than resting on the machines, with a small gap above them for vibration and so they can be slid out for servicing. Standard front-loading machines usually fit under a standard-height worktop, but we check the appliance heights against the plan first.

Can a utility room go in a garage or under the stairs?

Often, yes, as long as the space already exists and is usable. In a garage it needs to be dry and protected from frost, with power and a route for water and waste. Under the stairs, check the headroom, the ventilation and whether a door can open fully. We fit units and connect appliances in existing spaces; converting a garage into a habitable room is a separate building project.

Also covering nearby towns

The same service is available a short drive from Bolton, including: