Utility room fitting in Battersea

Is utility room fitting right for your Battersea kitchen?

When a new kitchen is being planned in Greater London, moving the laundry to a utility often makes room for deep drawers or a dishwasher in the kitchen itself.

In a Battersea house where the garage is already used for storage rather than the car, some people fit a run of units and the laundry along one wall. Kitchens in every part of Battersea are covered, and the survey visit is free wherever you are in Greater London.

What is included in the work?

Every kitchen is different, so we confirm the scope in writing. Most jobs of this kind include:

Base, wall and tall units fitted, levelled and fixed to the wall
Washing machine supply, waste and isolation valve, tested for leaks
A vent to outside for a vented dryer, or a drain hose for condenser models
Utility sink and tap plumbed in, with new supplies and waste where none exist
Stacking kit fitted where the washer and dryer sit one above the other
Free survey visit to check water, waste, power and outside wall positions

What does utility room fitting cost in Battersea?

Use these ranges to plan your budget. They include VAT, reflect costs in London, and are firmed up once we have seen your Battersea kitchen. Prices in London usually run above the national guide, mainly because labour and parking cost more.

What does utility room fitting cost in Battersea?
Typical project	Guide price
Utility units and worktop fitted (fit only)Three to six units, laminate worktop, panels	£1,600–£3,900
Utility room supplied and fittedUnits, worktop, sink, washer and dryer connections	£3,900–£9,100
New utility plumbing for a sink and washing machineSupplies, waste and valves where none exist	£520–£1,300

Fit-only and supply-and-fit ranges cover units, worktop and standard sink and appliance connections, with new plumbing where none exists as a separate line; extract fans, dryer vents and new circuits are quoted on top. Prices include VAT at 20%.

Kitchens in homes around Battersea

Typical homes in this part of Greater London include Victorian and Edwardian terraces, conversion flats, mansion block flats and 1930s semis. Victorian terraces often have a narrow galley beside the side return, while conversion flats and mansion blocks usually fit the kitchen into a small room or along one living-room wall.

Permit parking, red routes and flats without lifts are common, so parking suspensions, stair carries and lift bookings may need arranging before delivery day. London's mains water is hard, so limescale builds quickly on taps and boiling water taps, and a scale-reducing filter is worth planning in.

Do you need approval for utility room fitting in Battersea?

Fitting a utility room needs no planning permission in England, though a new dryer vent through the outside wall of a flat may need planning permission and the freeholder's consent. Adding sockets to an existing circuit is not notifiable, but a new circuit is, under Part P. Approved Document F sets an extract rate of about 30 litres per second for a utility room, so a new fan should be sized to meet it, and if an open-flued boiler shares the room, a Gas Safe registered engineer should carry out a spillage test once a fan is fitted.

Conservation areas are widespread across London, so a new extractor vent on a front wall may need permission, and leaseholders usually need the freeholder's written consent first.

Practical advice for Battersea homeowners

Before choosing a dryer for your Battersea utility, check whether there is an outside wall close enough for a short, straight vent duct.
If your Greater London home has an open-flued boiler in the utility, ask for a spillage test by a Gas Safe registered engineer once an extract fan goes in.
If the utility will be in the garage of your Battersea home, make sure the space stays above freezing in winter for the pipes and machines.
A worktop over appliances needs support at each side and a gap above the machines, so they can be slid out for servicing.

Questions about utility room fitting in Battersea

How much does utility room fitting cost in Battersea?

Guide prices in Battersea are about £1,600 to £3,900 including VAT for fitting three to six utility units and a worktop you have bought. The final price depends on the size of the kitchen and what is moving, and is set out in an itemised written quote.

Do you work near Battersea as well?

Yes. As well as Battersea itself, we cover the rest of Greater London and nearby towns such as Chelsea and Pimlico. The process is the same wherever the kitchen is.

Can a worktop go over a washing machine and dryer?

Yes, and it is one of the most common utility layouts. The worktop is supported by units, end panels or a rail at each side rather than resting on the machines, with a small gap above them for vibration and so they can be slid out for servicing. Standard front-loading machines usually fit under a standard-height worktop, but we check the appliance heights against the plan first.

Does a utility room need an extractor fan?

Yes, in most cases. Washing and drying put a lot of moisture into a small space, so extract ventilation is strongly advised: Approved Document F sets a rate of about 30 litres per second for utility rooms in England and Wales, and the building standards in Scotland and Technical Booklet K in Northern Ireland cover ventilation too. An extract fan ducted outside is the usual answer, with a window helping but not replacing it. A vented dryer needs its own duct as well.

Does a condenser or heat pump dryer need an outside vent?

No. Condenser and heat pump dryers do not need an outside vent, so they can go where a vented dryer cannot. They collect water in a container that has to be emptied, or they can be connected to the waste so they drain automatically, which is easy when the dryer sits beside the washing machine. They still give off some warmth, so the space needs air around it. A vented dryer needs a duct to an outside wall.

Utility room fitting in neighbouring towns

Close to Battersea? We cover these nearby towns too: