Kitchen Installers UK

Utility room fitting · Surrey

Utility room fitting in Ashford, Surrey

Need utility room fitting in Ashford, Surrey? Tell us about the kitchen and we will arrange a free, no-obligation survey to see what the job really involves.

Guide price£460 to £8,000
Postcodes includeTW15
Timescale1 to 3 days on site
A utility room with a stacked washing machine and dryer, a small sink, a tall cupboard and a laminate worktop

What prompts utility room fitting in Ashford, Surrey?

In an Ashford, Surrey house where the garage is already used for storage rather than the car, some people fit a run of units and the laundry along one wall.

If your Ashford, Surrey home has a back lobby or a rear porch with a little spare width, a few units and a stacked washer and dryer can make it a working utility. We cover all of Ashford, Surrey, including the TW15 postcode district, and travel out to neighbouring towns across Surrey.

What is included in the work?

Here is what usually goes into utility room fitting, adjusted to your Ashford, Surrey kitchen after we have measured it:

  • Worktop over the washing machine and dryer, supported clear of the appliances
  • Utility sink and tap plumbed in, with new supplies and waste where none exist
  • Base, wall and tall units fitted, levelled and fixed to the wall
  • Washing machine supply, waste and isolation valve, tested for leaks
  • Free survey visit to check water, waste, power and outside wall positions
  • Stacking kit fitted where the washer and dryer sit one above the other

Utility room fitting prices in Ashford, Surrey

Typical utility room fitting prices for homes in Ashford, Surrey, including VAT and adjusted for the South East. Your own figure depends on the size of the kitchen, the layout and what is moving. Prices in the South East usually run above the national guide, mainly because labour and parking cost more.

Utility room fitting prices in Ashford, Surrey
Typical projectGuide price
Utility units and worktop fitted (fit only)Three to six units, laminate worktop, panels£1,400–£3,400
Utility room supplied and fittedUnits, worktop, sink, washer and dryer connections£3,400–£8,000
New utility plumbing for a sink and washing machineSupplies, waste and valves where none exist£460–£1,200

Fit-only and supply-and-fit ranges cover units, worktop and standard sink and appliance connections, with new plumbing where none exists as a separate line; extract fans, dryer vents and new circuits are quoted on top. Prices include VAT at 20%.

Local homes and their kitchens

The housing mix across Surrey includes 1930s semis, Victorian and Edwardian villas, detached family houses and new-build estates, so no two kitchen fits are quite alike. 1930s semis often have a narrow kitchen beside the dining room, while larger detached houses and Edwardian villas may have room for an island or a separate utility.

Surrey's water is hard across most of the county, so limescale on taps and boiling water taps is common, and a scale-reducing filter is worth considering. Private roads, long drives and village lanes can be awkward for large lorries, while town-centre flats may need lift bookings and parking permits for delivery day.

Regulations for kitchen work in Ashford, Surrey

Fitting a utility room needs no planning permission in England, though a new dryer vent through the outside wall of a flat may need planning permission and the freeholder's consent. Adding sockets to an existing circuit is not notifiable, but a new circuit is, under Part P. Approved Document F sets an extract rate of about 30 litres per second for a utility room, so a new fan should be sized to meet it, and if an open-flued boiler shares the room, a Gas Safe registered engineer should carry out a spillage test once a fan is fitted.

Listed buildings and conservation areas in older towns and villages may need consent for new vents, and flats in managed blocks usually need the freeholder's consent first.

Before you book utility room fitting in Ashford, Surrey

  • If your Surrey home has an open-flued boiler in the utility, ask for a spillage test by a Gas Safe registered engineer once an extract fan goes in.
  • Ask for an isolation valve on the washing machine supply that can be reached without pulling the machine out from under the worktop.
  • Before choosing a dryer for your Ashford, Surrey utility, check whether there is an outside wall close enough for a short, straight vent duct.
  • A worktop over appliances needs support at each side and a gap above the machines, so they can be slid out for servicing.

Questions about utility room fitting in Ashford, Surrey

How much does utility room fitting cost in Ashford, Surrey?

Guide prices in Ashford, Surrey are about £1,400 to £3,400 including VAT for fitting three to six utility units and a worktop you have bought. The final price depends on the size of the kitchen and what is moving, and is set out in an itemised written quote.

Do you cover all of Ashford, Surrey?

Yes. We work across Ashford, Surrey, including the TW15 postcode district, and nearby towns such as Staines and Feltham. Book a free survey visit and we will arrange a time that suits you.

Does a utility room need an extractor fan?

Yes, in most cases. Washing and drying put a lot of moisture into a small space, so extract ventilation is strongly advised: Approved Document F sets a rate of about 30 litres per second for utility rooms in England and Wales, and the building standards in Scotland and Technical Booklet K in Northern Ireland cover ventilation too. An extract fan ducted outside is the usual answer, with a window helping but not replacing it. A vented dryer needs its own duct as well.

Can a utility room go in a garage or under the stairs?

Often, yes, as long as the space already exists and is usable. In a garage it needs to be dry and protected from frost, with power and a route for water and waste. Under the stairs, check the headroom, the ventilation and whether a door can open fully. We fit units and connect appliances in existing spaces; converting a garage into a habitable room is a separate building project.

Can a worktop go over a washing machine and dryer?

Yes, and it is one of the most common utility layouts. The worktop is supported by units, end panels or a rail at each side rather than resting on the machines, with a small gap above them for vibration and so they can be slid out for servicing. Standard front-loading machines usually fit under a standard-height worktop, but we check the appliance heights against the plan first.

Also covering nearby towns

The same service is available a short drive from Ashford, Surrey, including:

More services for Ashford, Surrey kitchens

Free survey visit

Book a free survey visit in Ashford, Surrey

We measure up, check walls, floors and service positions, and send an itemised written quote. Or get a guide price online in about two minutes.

Book a free survey visit

Tell us about the kitchen and the work. We will call to arrange a visit.

We use your details only to arrange your visit and quote. See our privacy notice.

Prefer to talk? 0800 088 6341

CallGuide price