Kitchen worktop fitting in Montrose

Why kitchen worktop fitting for a Montrose home?

Some homeowners across Dundee and Angus have already ordered stone worktops from a supplier and need someone to fix and level the base units so templating can go ahead.

If your Dundee and Angus kitchen still has a dated tiled or laminate surface, new worktops often go in with a new sink, tap and splashback at the same time. Montrose sits about 26 miles north-east of Dundee, and our Dundee and Angus coverage takes in everything in between.

What is in a typical job?

The exact scope is agreed after the survey, but a typical job in Montrose covers:

Free survey visit to measure the runs and check the base units are level
Matching upstands fitted and the joint to the wall sealed
Sink, tap and hob reconnected, with gas hobs connected by Gas Safe registered engineers
Laminate jointed with a mason's mitre or joint strips, and every cut edge sealed
Undermount sink and hob cut-outs cut and finished by the stone fabricator
Old worktops removed and taken away, with the sink and hob disconnected safely

What should you budget for kitchen worktop fitting in Montrose?

The figures below are guide prices for Montrose, including VAT and adjusted for typical costs across Scotland. The fixed price comes after we have measured up. Prices in Scotland usually come in below the national guide, as labour rates are lower than in the South East.

What should you budget for kitchen worktop fitting in Montrose?
Typical project	Guide price
Laminate worktops, supplied and fittedTypical kitchen, joints, cut-outs and upstands	£470–£1,100
Solid wood worktops, supplied and fittedOiled before and after fitting	£850–£1,700
Granite, templated and fittedTemplate visit, cutting, delivery and fitting	£1,400–£3,000
Quartz, templated and fittedTemplate visit, cutting, delivery and fitting	£1,700–£3,300
Old worktops removed and taken awayMore for stone	£80–£240

Guide ranges are for a typical kitchen and include the worktops, cut-outs, upstands and fitting; removing old tops is a separate line, and new sinks, taps and splashbacks are priced on top. Prices include VAT at 20%.

Local homes and their kitchens

In and around Montrose, homes range across sandstone tenement flats, Victorian villas, post-war council-built houses and fishing town cottages. Dundee's tenement flats often have a narrow kitchen or a box room off the hall, while villas in Broughty Ferry and the Angus towns tend to have larger separate kitchens.

Dundee and Angus have soft mains water, so limescale is rarely an issue and taps and boiling water taps tend to stay free of heavy scale. Common stairs in tenements, steep streets in parts of Dundee and narrow glen roads in Angus can each affect deliveries and worktop lengths.

Building regulations, electrics and gas in Montrose

In Scotland, replacing worktops counts as replacing fitments, so it does not need a building warrant. Any electrical changes, such as new sockets above the worktop, must meet the building standards and BS 7671, and you should ask for an electrical certificate. Gas hobs must be disconnected and reconnected by a Gas Safe registered engineer, and a sink needing a new underground drain connection would need a warrant first.

Consent may be needed for new vents on listed buildings and in conservation areas, and homes in the upper Angus glens fall within the Cairngorms National Park.

Practical advice for Montrose homeowners

Before templating day at your Montrose home, make sure the sink, tap and hob are on site so the stone can be cut to them.
If your Montrose kitchen has a gas hob, a Gas Safe registered engineer needs to disconnect it before the old worktops come off.
If your Dundee and Angus home has uneven walls, ask how the worktop will be scribed so the back edge meets the wall without wide gaps.
Stone worktops are templated only once the base units are fixed and level, so allow one to two weeks between fitting and finishing.

Questions about kitchen worktop fitting in Montrose

How much does kitchen worktop fitting cost in Montrose?

Kitchen worktop fitting in Montrose typically costs £470 to £1,100 including VAT for laminate worktops, supplied and fitted, based on prices in Scotland. Larger or more involved jobs cost more, and your price is fixed in writing after a free survey visit.

Do you work near Montrose as well?

Yes. As well as Montrose itself, we cover the rest of Dundee and Angus and nearby towns such as Brechin and Arbroath. The process is the same wherever the kitchen is.

Will you fit stone worktops I have ordered myself?

Yes, alongside your stone supplier. Stone must be templated and fabricated by the supplier once the base units are fixed and level, so our part is getting the units ready, checking they are sound and reconnecting the sink, tap and hob after the stone is in. Laminate and wood worktops you have bought can be cut, jointed and fitted on site in the usual way.

How long does it take to fit new worktops?

Usually a day for laminate or solid wood in a typical kitchen, cut and jointed on site. Stone takes two visits: the fabricator templates once the base units are fixed and level, then cuts the worktops, the sink and hob openings and any drainer grooves, and fits them about one to two weeks later. In the meantime the sink is usually out of use, so plan meals around that gap.

How are laminate worktops joined at corners?

With either a mason's mitre or a joint strip. A mason's mitre is routed with a jig so the front edge profile turns the corner, then glued, sealed and pulled tight with connector bolts underneath. A joint strip is a metal or colour-matched profile fixed and sealed between the two lengths. Either way, every cut edge, including the sink and hob cut-outs, is sealed so water cannot swell the core.

Nearby places we cover

We also carry out kitchen worktop fitting in these towns near Montrose: