Sink and tap installation in Portishead

Is sink and tap installation right for your Portishead kitchen?

If you are fitting new stone worktops in your Portishead kitchen, it is a natural point to change to an undermount sink cut and polished by the fabricator.

Homeowners across Somerset adding a boiling water tap often need a socket or spur in the sink cupboard, a filter and space for the tank planned in. Kitchens in every part of Portishead are covered, and the survey visit is free wherever you are in Somerset.

What we cover for sink and tap installation in Portishead

Here is what usually goes into sink and tap installation, adjusted to your Portishead kitchen after we have measured it:

New sink fitted, sealed and connected to the existing supplies and waste
Every joint leak tested, with water flow and drainage checked before handover
Inset sink cut-outs made on site in laminate and wood worktops
Sink moved to a new position with new supply and waste runs
Boiling water tap fitted with its tank, filter and power supply in the cupboard
Isolation valves on the hot and cold supplies, with flexible tap tails connected

Sink and tap installation prices in Portishead

Use these ranges to plan your budget. They include VAT, reflect costs in the South West, and are firmed up once we have seen your Portishead kitchen. Costs in the South West sit close to the national guide.

Sink and tap installation prices in Portishead
Typical project	Guide price
Sink and tap plumbed inIsolation valves, waste and trap	£210–£410
Boiling water tap installedTank under the sink, filter and power supply	£150–£360
Sink moved to a new positionNew supplies and waste run	£410–£1,000
Undermount sink in a stone worktopCut-out and polishing are done by the stone fabricator	Priced with the worktop

Guide ranges cover labour and fittings such as valves, tails and wastes; the sink and tap themselves are extra, and undermount cut-outs in stone are priced with the worktop by the fabricator. Prices include VAT at 20%.

Kitchens in homes around Portishead

In and around Portishead, homes range across Georgian townhouses, Victorian terraces, stone cottages and post-war estate houses. Georgian townhouses in Bath often have kitchens at lower-ground level or in flats on upper floors, while Victorian terraces in Taunton and Yeovil tend to have a narrow back galley.

Steep streets and controlled parking in Bath, upper-floor flats without lifts and narrow village lanes can each make delivering worktops slower. Somerset's mains water is mostly hard, so limescale on taps and boiling water taps is common, and a filter or softener can help keep them working well.

Regulations for kitchen work in Portishead

Replacing a sink and tap needs no approval in England, but the plumbing should meet the Water Supply (Water Fittings) Regulations 1999, including isolation valves and backflow protection. Connecting to an existing waste is routine, while a new connection to an underground drain involves building control. A new spur for a boiling water tap on an existing kitchen circuit is not notifiable under Part P, but it must meet BS 7671.

Bath is a World Heritage city with many listed buildings, and homes in Exmoor National Park or conservation areas may need consent for new vents or internal changes.

Tips before you start

Check the tap's hole size against the sink or worktop before ordering, as some taps need a larger hole than an existing sink provides.
Find the stopcock in your Portishead home before the plumber arrives and check it turns off fully, as older stopcocks can stick or let water past.
Ask for the dishwasher and washing machine hoses to be routed so they cannot kink behind the units once the appliances are pushed back into place.
Moving the sink means new supply and waste runs, so check the waste can fall properly to the drain or stack from the new position.

Questions about sink and tap installation in Portishead

How much does sink and tap installation cost in Portishead?

Guide prices in Portishead are about £210 to £410 including VAT for plumbing in a new sink and tap. The final price depends on the size of the kitchen and what is moving, and is set out in an itemised written quote.

Which parts of Portishead do you work in?

All of them. Our Somerset coverage takes in the whole of Portishead, including the BS20 postcode district, as well as surrounding towns such as Nailsea. If you are unsure, send us your postcode.

What is the difference between an inset and an undermount sink?

An inset sink drops into a cut-out from above, with its rim resting on the worktop, and suits laminate, wood and stone. An undermount sink is fixed beneath the worktop so the edge of the cut-out is exposed, which usually calls for a solid, water-resistant material such as stone or solid surface. Undermount cut-outs in stone are cut and polished by the fabricator.

Do I need isolation valves under my kitchen sink?

They are strongly advised, and we fit them as standard. An isolation valve on each supply to the tap, and on each appliance supply, lets you turn off the water to one fitting without shutting off the whole house. That makes changing a tap cartridge or dealing with a leak far simpler. The valves are left where they can still be reached once the cupboard is in use.

What do I need for a boiling water tap?

A boiling water tap needs a tank in the cupboard under the sink, usually a socket or fused spur to power it, and often a filter, particularly where the water is hard. Some models have a minimum water pressure, so check yours before buying. The tap also needs a correctly sized hole in the sink or worktop and enough clear cupboard space for the tank and pipework.

Sink and tap installation near Portishead

Neighbouring towns where we offer sink and tap installation: